Exercise 2 Given the function F = A.((B.C). (A + B + C + D)) a) Implement the function F using 4 to 16 decoder with active high output. b) Implement the function F using 3 to 8 decoder with active high output. c) Implement the function F using 4 to 16 decoder with active low output.

Exercise 2 Given the function F = A.((B.C). (A + B + C + D)) a) Implement the function F using 4 to 16 decoder with active high output. b) Implement the function F using 3 to 8 decoder with active high output. c) Implement the function F using 4 to 16 decoder with active low output.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

3- If we increased 2 bits of the ADC quantizer, what is the improving in the SNR will be? Discussed your answer.
Write VHDL code for a modulo-13 counter (counting sequence is 010, 110, …. 1210). The counter has the following features: a synchronous Active High Reset a value R can be loaded into the counter, using the signal Ld (Load) The signal Ld is active High Draw the schematic of your counter, showing the inputs and outputs. Show the number of bits for R, Q (output of the counter), Ld.
Q3: Assume that you have to spread two signals A and B, using CDMA with the DSSS. The data of signals are Ad = 111 and Bd = 000. The key sequences are Ak = 010100 100010 110011, and Bk = 000110 101000 010111 If the binary "0" is assigned a positive signal value (+1), the binary "1" a negative signal value (-1), for the As and Bs. Find the following: 1. The results of spreading signals As and Bs. 2. The summation signal of As + Bs. 3. Find the output data values of As and Bs.
Exercise 1 e) Design a circuit that will detect the three-bit binary code at its input. The output must be logic HIGH to indicate the corresponding binary code. (Hint: decoder circuit). f) Design a circuit that will detect the three-bit binary code at its input. The output must be logic LOW to indicate the corresponding binary code. (Hint: decoder circuit).
III. Theory/ Discussion 1) Arduino IDE consists of 2 functions. What are they? a) else () and loop () b) Setup () and build () c) Setup () and loop () d) Setup () and elseif () 2) When forward biased, LED emits light because of Recombination of carriers and Light produced by collisions. 3) ATmega328p microprocessor is used in arduino UNO. (TRUE/FALSE) (TRUE/FALSE) IV. Circuit Diagram (Before Simulation) Draw the circuit and write the program codes by considering input pin as A2 and output and output pin as 9 for green, 10 for yellow LED & 11 for red LED. Also verify the results if (gas >= 100) red LED should glow, if (gas >= 60) yellow LED should glow, otherwise green LED should glow. V. Connection Diagram and Results after simulation hp
C D .accepts this data and redistributes it to the n outputs. encoder De-multiplexer are faster in speed because the delay between the input and. * *.accepts this data and redistributes it to the n outputs. Decoder O output is due to the propagation delay of gate combinational circuit O Sequential network O Integrated circuit O Decoder O encoder O De-multiplexer
QUESTION 3 a) One of Medium Scale Integrated (MSI) circuit application is to compare between two input binary quantities and generates outputs to indicate which one has the greater, equal, or lower magnitude. Design the circuit to compare between two 2-bit inputs, you may choose only one output. Justify your design. b) Design an encoder to perform number conversion between two different numbering systems.
b. Obtain the waveform of output states Q and for the SR when the input condition as in figure 5 is given. Figure 5 c. List out any five operating characteristics of flip flops. Q4 a. Based on your understanding on amplifiers and Oscillator, explain the operation of Hartley Oscillator, principle of operation and highlight the main applications. (write short note 80 words) b. For the given circuit in figure 6, determine the upper and lower frequencies of oscillation and also the Hartley oscillators bandwidth. +Vce RC HE (100. 200 PA L. mll La 2 ml Figure 6
2. PCM A voice signal is measured at 3.21692 V and it resides inside an interval from 3.20 V to 3.30 V. b) If there were 512 levels in the PCM encoder, how many bits would the sample above represent? HINT: L=2" d) If the total range of voltages started at zero and there are 512 intervals, what would the maximum possible voltage be? e) The original voice signal voltage and the decoded voltage value are different. What is this "round off error"? f) What is the ratio of received voltage to round off error in absolute and in dB form? This is signal to noise ratio for this digital system.
I have one question left. If ever please answer this three question? *Design a decoder that recognizes the decimal number 23. * Design an encoder circuit to generate the 3-bit binary gray code. Use positive NAND/Negative OR circuit. *What is the decimal equivalent of the state being decoded by the circuit in the figure.
A 10 bit binary "0110010111" is stored in a memory .What is its content if it represents in i) BCD code ii) Excess -3 code iii) 8421 code iv)Octal code v) Hexadecimal code
Explain the encoding technique of Digital Data to Analog Signal. by using the example