Example: In the reheated Rankine cycle shown in the figure, the boiler pressure is 6 MPa, the condenser pressure is 0.0096 MPa and T1=723 K, T3=573 K. Calculate the thermal efficiency, mass flow rate (kg/h) and heat removed from the condenser (MW). (P3=0.618 MPa and Wnet,actual=120 MW) T 6, 2

Example: In the reheated Rankine cycle shown in the figure, the boiler pressure is 6 MPa, the condenser pressure is 0.0096 MPa and T1=723 K, T3=573 K. Calculate the thermal efficiency, mass flow rate (kg/h) and heat removed from the condenser (MW). (P3=0.618 MPa and Wnet,actual=120 MW) T 6, 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A refrigerant 22 vapor compression system includes a liquid-to-suction heat exchanger in the system.…

A: (a) Draw the T-s diagram for the cycle without the heat exchanger. From the properties table for…

Q: 1. Consider the following schematic of a power plant (operating in what is called a 'Rankine Cycle')…

A: Given data: Mass flow rate (m) =25 kg/s Write thermal property value at the corresponding points…

Q: Sketch a commercial type outdoor air-cooled condenser. Discuss the heat transfer mechanism in the…

A: The sketch of the commercial air cooled condenser along with its working are as follows:

Q: The diagram to the right shows a typical schematic of a simple refrigeration system. We will learn…

Q: EXPLAIN HOW QUANTITY OF COOLING WATER IN A CONDENSER IS ESTIMATED.

A: The answer is in next step

Q: 1. Consider the following schematic of a power plant (operating in what is called a 'Rankine Cycle')…

Q: Calculate the vaccum efficienty of a condenser from the following data, Vaccum at steam inlet to…

A: The answer is in the next step

Q: A heat pump is required to deliver heat at 55oC with an evaporator temperature of -10oC. Calculate…

A: Given, TL = -10oC = -10+273 = 262 TH = 55oC = 55+273 = 328

Q: Airborne heat used to heat a home refrigerant circulating in the cycle of the pump-134a 600 kPa…

A: Given data: Heat from outside air is used to heat a home. For the heat pump, refrigerant R-134 a is…

Q: 11-59 Consider a two-stage cascade refrigeration system operating between the pressure limits of 1.4…

A: Refrigerant-134a P8 = 1.4 MPa P1 = 160 kPa P5 = 0.4 Mpa P2 = 0.5 MPa Isentropic efficiency = 80 %…

Q: The food storage room requires a cooling system with a capacity of 15 tons of refrigeration that…

A: Given data: - The cooling capacity is C = 10 tons. The evaporator temperature is T1 = -25.2 oC.…

Q: Distinguish between Contact condenser and Surface condenser.

A: Contact type condenser: 1. According to the name, the fluid is mixing in the contact type condenser.…

Q: Draw with esthetic a lithium bromide refrigeration cycle without any moving parts, and label every…

Q: PROBLEM 1 : A 50-ton vapor compression refrigeration system is to evaporate R-12 at -20°C and to…

A: “Since you have posted a question with multiple subparts, we will solve first three sub parts for…

Q: How to do a heat/energy balance on a anode fuel cell and a condenser given that the fuel cell is…

Q: Compute the power in KW generated by Agusan Hydro Blectric power plant with water flOw rate of 1,552…

A: Given: Water flow rate of the power plant→Q=1552 liters/sec…

Q: EXPLAIN HOW QUANTITY OF COOLING WATER IN A CONDENSER IS ESTIMATED.

Q: Calculate the power required in an ammonia system which serves a 100kW evaporator at -30 C . The…

A: Given data: TL=-30°C=243 KTH=32°C=305 KQL=100 kW Need to determine the power required in an ammonia…

Q: Q:absorption cycle used a water as refrigerant and Lithium Bromide as absorbent fluid. The mass rate…

A: To Find:The COP of the system Given:Mass flow rate of the flow is : m=0.5 kg/sTemperature of…

Q: Given that the temperatures of the generator, condenser, absorber and evaporator of a VARS system…

Q: The food storage room requires a cooling system with a capacity of 10 tons of refrigeration that…

A: Given: The refrigeration capacity, R = 10 tons = 35 kW The evaporator temperature, Te = -17.8 degree…

Q: 02. The Li-Br water absorption cycle operate at the following temperature: generator temperature =…

A: Generator Temperature, Tg = 90℃ = 363KCondenser Temperature, Tc = 35 ℃ = 308KAbsorber Temperature,…

Q: A 200 MW steam power plant operates on a simple Rankine cycle with superheated steam entering the…

Q: there is an update in the previous question - A Carnot refrigeration cycle absorbs heat at 250 K…

A: Data given- T1 = 250 K T2 = 300 K Q1 = 1130 kJ/min Or Q1 = (1130/60 )kJ/s

Q: . Calculate the heat effect for this heat pump cycle 2. Calculate the coefficient of performance…

A: From the pressure table of R134 a For cycle 1: At 80 kPa (saturated vapor) h1=231.46 kJ/kg…

Q: Evaluate the co-efficient of performance and heat transfer rate in the condenser of a refrigerator…

A: COP stands for Coefficient Of Performance and indicates the efficiency of heating and cooling…

Q: Given the following information about a condenser system, determine the fan power requirement, Fp:1.…

A: Power is defined as the rate of energy required to induce a mechanical motion. Flowrate is the…

Q: Explain the principle of operation of geothermal heat pump depicted in

Q: QI/ Refrigeration unit using R-134a as shown in figure below contains two compressors and two…

Q: The food storage room requires a cooling system with a capacity of 10 tons of refrigeration that…

A: From steam table of R-134a:- Specific enthalpy at compressor inlet, h1=hgat…

Q: Calculate the mass flow rate of the refrigerant.

A: Heat rejection from the refrigeration and heat pump system:Time taken for one cycle=0.7 sec.From the…

Q: How many BTUS are extracted in one hour?

A: To find BTU Extracted in one hour.

Q: For the purpose of acting as an air-cooled water chiller, an ammonia refrigerant vapor compression…

A: Note: As per the policy, we can solve the first three subparts unless it is mentioned to solve the…

Q: Why every condenser is not a heat exchanger

A: A heat exchanger is a device used to transfer heat between 2 substances at different temperatures.…

Q: Distinguish between following devices with its applications and examples: i.Compressor and Turbine…

A: Hydraulic machine is a mechanical device that uses liquid fluid power to perform work.

Question

Calculate the thermal efficiency, mass flow rate (kg/h) and heat removed from the condenser (MW).

Example: In the reheated Rankine cycle shown in the figure, the boiler pressure is 6 MPa, the
condenser pressure is 0.0096 MPa and T1=723 K, T3=573 K. Calculate the thermal efficiency, mass
flow rate (kg/h) and heat removed from the condenser (MW).
(P3=0.618 MPa and Wnet,actual=120 MW)
T
6
2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 10 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The food storage room requires a cooling system with a capacity of 15 tons and refrigeration that operates at an evaporator temperature of -17.5 degrees Celsius and a condenser temperature of 37.0 degrees Celsius. The refrigerant used is R - 134 A and the operating system is saturated. Determine C.O.P, refrigerant flow rate and heat loss rate in the condenser.
5.18 : Taking the data of the preceding problem except the final temperature of the cooling water is to be taken to apply to a jet condenser, calculate the weight of injection (cooling) water required per kg of steam.
What is the answer of the following asked: (need solution ASAP, thank you)The heat rejected in the condenser in kJ/kg is:The net work in the turbine in kJ/kg is:
The food storage room requires a cooling system with a capacity of 10 tons of refrigeration that operates at an evaporator temperature of -17.8 ° C and a condenser temperature of 30.1 ° C. The refrigerant used is R-717 and the system operates in saturated conditions. Determine C.O.P , Refrigerant flow rate , Heat loss rate in condenses
A food storage chamber requires a refrigeration system of 15 ton capacity operating at an evaporator temperature of -25.2 deg C and a condenser tempreature of 35.8 deg C. Refrigerant (R-717) is used and the system operates under saturated conditions. Determine: a.) C.O.P. b.) Refrigerant flow rate c.) Rate of heat flow removed by condense
Specify The C.O.P. of the cycle refrigeration vapor compression a simple R-717. Temperature evaporation is -20 °C and the temperature of the condenser is 30 °C (C.O.P is found using enthalpy)
1. A standard vapor compression refrigeration system uses Ammonia as refrigerant. The Ammonia leaves the evaporator at – 20 degree Centigrade and the condenser pressure is 1200 kPa. The flow rate is 30 kg/min. Determine a) the tons of refrigeration b) the power required c) the COP.
At 10kPa pressure and dryness degree x=0.90, the steam coming out of the turbine goes to the pump with adiabatic efficiency of 0.85 after condensing in the condenser. The pump sends the condensed water to the steam boiler with a working pressure of 8MPa. a) Find the h.T values of the inlet points of the condenser, pump and boiler b) Since the flow rate of the condensed water is 9000 kg/h, find the load of the condenser c) Find the power of the pump
The food storage room requires a cooling system with a capacity of 10 tons of refrigeration that operates at an evaporator temperature of -17.8 ° C and a condenser temperature of 33.9 ° C. The refrigerant used is R-717 and the system operates in saturated conditions. questions a. COP = Answer. b. Refrigerant flow rate = Answer kg / s. c. Heat loss rate in condenser = Answer kJ / s
6- The following reading were taken during a test on a surface condenser: Mean condenser temperature = 35°C Hot well temperature = 30°C Condenser vacuum = 69 cm Hg Barometer reading = 76cmHg Condensation rate = 16 kg/min Cooling water temperature inter = 20 °C Cooling water temperature outlet = 32.5 °C Flow rate being = 37500 kg/h Calculate: a- mass of air present per cubic meter of condenser b- quality of steam at condenser inlet c- vacuum efficiency d- condenser efficiency (condenser heat transfer effeteness)