Example H.VW: Consider the ideal Currentamplifier. Assume that the source resistance is RsµA, Ifp = 99 µA, and I, = 5 mA, determine A¡, Bị , and A¡FB, includingunits. (b) Using the results of part (a), determine Zier and ZOFB forRi = 5 k2 and Ro = 4 k2. (Ans. (a) A = 5000 A/A, B; = 0.0198 A/A,Airn = 50 A/A (b) Zirr = 502, ZOFR = 400 k2)Shunt feedback=00. (a) If I = 100%3D%3DlFB

Feedback System: Feedback Systems are signal processors because they process signals. A feedback…

Example H.W: Consider the ideal Current amplifier. Assume that the source resistance is R, =00. (a) If I = 100 µA, Ifp = 99 µA, and I, = 5 mA, determine A¡, Bi , and AjFp, including units. (b) Using the results of part (a), determine ZiEn and ZorR , for Ri = 5 k2 and Ro = 4 k2. (Ans. (a) A = 5000 A/A, B; = 0.0198 AA, Aien = 50 A/A (b) Zirr = 502, ZofB Shunt feedback - %3D FB FB %3D %3D %3D 400 k2) %3D %3D

Example H.W: Consider the ideal Current amplifier. Assume that the source resistance is R, =00. (a) If I = 100 µA, Ifp = 99 µA, and I, = 5 mA, determine A¡, Bi , and AjFp, including units. (b) Using the results of part (a), determine ZiEn and ZorR , for Ri = 5 k2 and Ro = 4 k2. (Ans. (a) A = 5000 A/A, B; = 0.0198 AA, Aien = 50 A/A (b) Zirr = 502, ZofB Shunt feedback - %3D FB FB %3D %3D %3D 400 k2) %3D %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a circuit to simulate the following mathematical equation using minimum number of operational amplifiers. 5f Vout = 12V1 +5 V2 dt + 6 Where Vout is the output voltage, V1 and V2 are the input voltages. Assume that the available Dc source is +/- 5 volt.
show maximum details please .. thanks a lot
Apply the current divider formula twice to derive an expression for the source-to-load gain formula io/is
An ideal boost converter is utilized in designing a PV storage system. The boost converter is operating at the boundary layer between the continuos conduction mode and discontinuous conduction mode. Design the mathematical model of the switching frequency for this boost converter in terms of load, duty cycle and inductance under the above operating conditions.
For the BJT circuit shown below, sketch the hybrid equivalent model circuit with labels of voltages, impedances, and currents. ... 1.8k0 Vo 39ka 22ko tuF-POL 10UF-POL 1200 1uF-POL 2N2221 100mv 1.5KHZ ODeg
2. How the characteristics of the voltage follower (i.e., the high input and low output impedance) affect the voltage appearing across the load resistor? Support your answer using analytical analysis.
help me please..................
Given the circuit in figure. Derive the formula of voltage gain and current gain using complete hybrid pi model. Draw the AC equivalent circuit
Perform an ac analysis. Represent the amplifier by its ac equivalent circuit and discuss the input resistance at the base and the output resistance. (You can draw the circuit by hand on paper and can paste the image)
Subject: Analogy Electronic and Circuit Derive Output Impedance & Voltage Gain for self bias un-bypass circuit using hybrid model
3. For the following circuit assumer, = 33.4 N a. Draw the small signal equivalent circuit. b. Find the input impedance. c. Find output impedance. d. Find the voltage gain. -10 V 68 k2 4.7 kA e. Find the current gain. a = 0.998 10 uS
C. A variable capacitor. O d. An amplifier. When operating in the saturation region, the current gain 'B' of the bipolar transistor increases Select one: OTrue O False Assume Is= 8x 105 A, B-100, and VA =-. For the circuit shown below and for -0.5 mA, the value of the transconduce Vcc=2 V Q1