02:03 40D00 •O a ull al 90%i< TitleExample: A 10 MVA, 3 phase, Y connected, two pole,60 Hz, 13.8 KV, line to line turbo generator has air gapcharacteristic depicted in the following data:O.c.C. Vph : 2700,5500, 7200,8200 , 8800, 9400,9600, 9900 , 10200S.C.C. I SC : 130 250 490 620 740 850If:50 100 150 200 250 300350 400 450The armature winding resistance is 0.07 Q per phaseand the armature winding leakage reactance per phaseis1.9 Q. Find the field current that produces rated terminalvoltage when rated armature current is delivered to 0.8lagging power factor for three phase balanced load.1/1

Given Current (I) = 10 MVA Phase voltage (V)…

Answered: Example: A 10 MVA, 3 phase, Y…

Similar questions

Refering to the figure (AC bridge which used to calculate the unknown capacitor ): if Lx =70 cm and Cx2 = 100μF, Cx1 =200uF then Cx2 equal to : Cx1 Cx2 Lx Oscilloscope wwwwww Ls 12 ○ a. 100μF O O b. 700μF O c. 300μF O d. 200μF
The value of the rms current is most nearly A. 154 mA The current in the circuit is given by i(t) = I cos[(9580 rad/s)}), where I is the amplitude current. The voltage amplitude of the AC source is 112 V. B. 272 mA C. 384 mA D. 121 mA E. 334 mA R = 335 N C = 0.625 µF L = 75.8 mH
X2. A transmission line that has a resistance per unit length of 4.50x10−4 /m is to be used to transmit5.00 MW across 400 mi (6.44x105 m). The output voltage of the source is 4.50 kV. (a) What is the lineloss if a transformer is used to step up the voltage to 500 kV? (b) What fraction of the input power is lostto the line under these circumstances? (c) What If? What difficulties would be encountered in attemptingto transmit the 5.00 MW at the source voltage of 4.50 kV?
A series RLC AC Circuit is connected to a 110 volt generator line with A frequency of 60Hz. If the R = 1000 Ohms , L =3 H and C =2 μF, Find a)The XL, Xc , and total Z b) line current I c) Voltage drops VR , VL , and Vc ,
TC 5. A circuit connected to an ac generator has & = 31.4sin ( wt 4. --). With w = 350 rad/s. The 0.622 sin (wt -=).a) At what time does the generator reach maximum (ot current is given by I = %3D 4 emf for the first time? B) What time does it reach the max current c)If the circuit has only one element is that a capacitor inductor or resistor, explain d) Find the value of that element( Ans: a)6.7 ms b0 11.2 ms c) Inductor d) 144 mH ins prt sc delete f12 f10 A fs f6 17
A 120-V AC input is given to the primary of an ideal transformer with 800 loops at the primary and 200 loops at the secondary. What is the voltage at the secondary side? ○ 40 V ○ 480 V 120 V ○ 30 V
In a standard RLC circuit that we are looking at R = 0.075 Ω , L = 1.2 H and C = 1.6 F. The initial charge carries by the capacitor is Q0 = 0.045 C. The switch is closed at time t = 0. Calculate the value of Q, in coulombs, at time t = 1s.
A transformer has 100 turns on the primary and 300 turns on the secondary. The primary rms voltage is 12 V and the load is 30 ohms. Find the rms voltage across the load, the rms current through the load, and the rms current in the primary. O 36 V, 1.2 A, 3.6 A O 4V, 0.13 A, 0.4 A O 36 V, 0,4 A, 1.2 A O 36 V, 1.2 A, 1.2 A