Example 9.2. From two triangulation stationsA and B the clockwise horizontal angles to a station C were measured as ZBAC-50°05'26 and ZABC 321°55'442. Determine the coordinates of C given those of A andB are E 1000.00 m N 1350.00 m E 1133.50 m N 1450.00 m.

Q: What is the relationship between sensitivity and radius?

A: The change in angle or gradient of the level that results in movement of the bubble is known as…

Q: Draw a figure of door and label it

A: The figure and door is in next step

Q: Compare and contrast the uses of T-square and setsquares.

A: T-square: It is a technical instrument that is used for drawing purposes.  It is mainly used by…

Q: QUESTION 2 120 8 22- 14 - 40 70 56 34 44 R8 024 e 12 O8-2 Holes 64 26 34 22- STEPS: 56 1) Draw the…

A: For given isometric view, we identify the direction of the view. after identify that we can able to…

Q: Draw the frontside and topview the Shape Shown

A: Asked: To draw the front, side and top view of the given shape.   The required engineering id drawn…

Q: Additional Problem #2 30 mm Locate the centroid of the cross-sectional area at right. Sketch the…

A: The given figure is shown below:

Q: kindly resolve or recheck. thank you

A: Given data:

Q: he top, front and side views of Figure 2 with scale 1:1. The dime to the drawings.

A: Here they have given an object to draw top view, front view, and side view projections. Top view…

Q: 3 cm 7 cm 5 cm 5 cM Detenmine the Folloeing %3D

A: Calculation of area and moment of inertia

Q: ssed steel band acts as a line printer, creating the letters on the sheet of paper. Provide an…

A: The printing mechanism of a line printer is a metal band, or loop, of type characters is known as…

Q: Find the vertical and horizontal line detect segmentation

A: Detecting vertical and horizontal lines in an image is a common task in image processing and…

Q: The ABC rod is supported from point B and is in equilibrium with a force F1 = 12KN applied from…

A: Given Data: The equilibrium force F1 is, F1=12 kN The shear strength at pin B is, τs=350 MPa The…

Q: Enlarges or reduces selected objects, keeping the proportions of the object. explode command…

A: Answer - Scale command Explanation- Enlarges or reduces selected objects, keeping the proportions…

Q: Explain the Methods of Slices.

A: Methods of Slices may be used along the failure plan in different shearing resistance for soil.

Q: express each measurement in feet.42 inches

A: Given: The measurement is 42 in.

Q: lo" A 992 steel 14" -2" what is Mp= ? 14"

A: From the given data calculate all areas find the y bar find the Ix

Q: What are the classes of hardboard?

A: Hardboard has high density and high strength, which is a quality substitute for wood and is commonly…

Q: Step 5 incomprehensiable

A: In the step 5Settlement can be calculated using as below

Q: determine the degree of indeterminacy.

A: * Hinge support: - It is defined as the support which resists horizontal and vertical reaction but…

Q: Name the several types of drive hammers.

A: The drive hammers are generally used for driving the pile in the pile foundation.   The several…

Q: Define Shotcrete.

A: In a block of conventional concrete, the concrete is placed, and then it is compacted. But in…

Q: What is Sloped Glazed.

A: Glazing: The installation of glass to the building components or interiors of the structure is…

Q: Given the multiview projection of the solid, draw the isometric view.

A: Projection: - It is defined as image or figure of an object on a plane which is formed by joining in…

Q: DIFFERENT ACCESSORIES IN THE SHAPER MACHINE WORKS VERTICAL AND HORIZONTA

A:

Q: Draw the front, Side and top

A: For this, we can draw the diagram in Autocad. I have used the same to draw the diagram and have…

Q: Section lining or crosshatching is also known as a …?   A. Section pattern B. Hatch pattern C.…

A: Section lining referred as cross-hatching ,is used to indicate material in the sectioned part.

Q: How

A: 1 and 1 actually is the ratio representation of slope.

Q: 20ド Sm 10m

A:

Q: Define Steel Area

A: Answer Introduction Steel is the most important material used in the field of construction. Steel is…

Q: How does a Rube Goldberg machine works?

A: Rube Goldberg was a cartoonist and engineer who was known for making cartoons with complex…

Q: Describe a good rule of thumb for relating inches and centimeters?

A: For converting inches to centimeters, always remember inch is always bigger than centimeters.

Q: Which tools that can be used to :1 draw the following shape in .AutoCAD Left-side view Top view…

A: Answer: 4. Construction Lines, Offset, Line, Trim, Layers

Q: can you show the sides with dimensioning

A: To show the sides with dimensioning

Q: Calculate the second moment of area for a 50 mm ×100 mm stud with the actual dimensions shown on…

A: Given:- The dimension of the stud = 50 mm × 100 mm  The actual dimension of the stud = 45 mm × 105…

Q: Picture Name Uses

A: Name of tool - Wood Rasp Files Use - Used in carpentry for removal of excess material.

Q: Where do I get Ix from?

A: Bending stress formula:or, M/ = Z  {here, Z = I/y}or, Z= = 1.376 x 106 mm3W 18 x 50 has Z = 1.557 x…

Q: "There are 33 dowels - 10M, each measuring 1110 mm, in a continuous concrete footing. What is the…

A: Length of one dowel = 1110 mm                                        =1.11 m  Total no of dowel = 33…

Q: Give a description of the band printer.

A: Step: 1 Printer: - It is a machine which prints out electronic data onto paper like text files or…

Q: Compute the net area A, of the shape shown. Report your answer in in to the nearest two decimal…

A:

Q: What do you mean by intergranular?

A: I Intergranular is a term that is used to indicate that an angular space is occupied by a crystal…