Example 4. Flow between two reservoirs. Water at 10°C flow from a large reservoir to a small one through a 5-cm-diameter cast iron piping system shown in figure (6). Determine the elevation 2₁ for the flow rate of 61/s. Z₁ = ? @ Sharp-edged entrance, K₂ = 0.5 Standard elbow, flanged, K₂ = 0.2 = 4 m Gate valve fully open K₁ = 0.3- -Exit, K₂ = 1 (Answer. 27,9 m) 20 D = 5 cm -System boundary 9 m 80 m Figure 6:

Example 4. Flow between two reservoirs. Water at 10°C flow from a large reservoir to a small one through a 5-cm-diameter cast iron piping system shown in figure (6). Determine the elevation 2₁ for the flow rate of 61/s. Z₁ = ? @ Sharp-edged entrance, K₂ = 0.5 Standard elbow, flanged, K₂ = 0.2 = 4 m Gate valve fully open K₁ = 0.3- -Exit, K₂ = 1 (Answer. 27,9 m) 20 D = 5 cm -System boundary 9 m 80 m Figure 6:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Include proper explanation this is fluid mech problem
The flow is opened to the atmosphere at point D which is fed by a very wide reservoir that has a water surface elevation of (5+) meters as shown in the figure given below. Elevation of the horizontal axis BC is 1 meter. At sections AB the diameter of the pipe is (0.2+- meters and CD the diameter of the 100 pipe is (0.3+: meters. The flow is ideal (inviscid) and absolute atmosphere pressure is 9.81 N/cm?. Considering the pipe's diameter is (0.15+; m at section BC, find the discharges and the 100 а. velocities of the flow at other sections (AE, EB, BC, CF, FD). Draw the energy and hydraulic grade lines of the system. b. Assuming the system discharge is constant and has the value you have found in (a), calculate the minimum pipe diameter that the section BC can take and draw the energy and hydraulic grade lines of this situation. Note: Absolute vapor pressure of water is 2.26 kN/m?. 10 A E 2.5 D B m
A pump is discharging 12 lit/sec ofwater through 100mm diameter smooth steel pipe. When the pump is 720 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assumingf= 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 2 45 m 540m - 100mm dia
Water flow at a 250mm diameter horizontal pipe 90m long. The friction factor is 0.023. If the pressure at the starting point is 80KPA and the pressure at the end point is 50KPA. Determine the discharge at the pipe. A Q = 118.43 L/s В Q = 132.74 L/s Q = 101.07 L/s D Q = 172.81 L/s Q = 153.68 L/s No answer among the choices
Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of the transmission line is at point A 1 km downstream of the supply reservoir and the low point of the transmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the diameter of the pipe is 750mm and the pressure at A is to be 350 kPa. A) estimate the head that must be added by the pump. B) estimate the power supplied by the pump. C) calculate the water pressure at B.
A steel pipe is used to drain water from a reservoir that is 50 m above the datum, and water is discharged into the air at the elevation of the datum. The pipe is 1500 m long and 450 mm diameter and 50 mm wall thickness. A valve is installed at the downstream end of the pipe allows a flow rate of 0.71 m³/s. The valve was completely closed in 1.4 sec. Calculate maximum hammer pressure at the valve. The pipe is longitudinally anchored. Eb = 2.1×10° N/m², Ec=1.9×10¹¹ N/m².
A 1 2 The three-reservoir system is shown below: 3 C The elevation of Reservoir at A is 140m and at Cis 50m. The flow rate at Pipe 1 from Reservoir A is 1.75 m/s. All pipes have a length of 500 meters, friction factor f - 0.02, and sizes namely: Pipe Diameter 1 (mm) = 600mm Pipe Diameter 2 (mm) = 500mm Pipe Diameter 3 (mm) - 400mm Determine the elevation of Reservoir B in meters.
SOLVE AND ANSWER MUST BE IN 3 DECIMAL PLACES
Water flows from Resorvoir A (Elev 133 m.) to a turbine (Elev 76 m.) then discharges into tailtrace B (Elev 30 m.) as shown. the head loss from (A) to (1) is 2 times the velocity head in the pipe, and the head loss from (2) to (b) is 1.49 times the velocity head in the pipe. if the flow rate in the pipe is 35 ft63/S, diameter of all pipes is 25 in., calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s.
None
Question 3) Water transmission line is constructed to transmit water from A reservoir to city with 200 l/s of total discharge. 150 l's is supplied from reservoir and the other part is added from B point (Use same types of pipes through the pipeline). Maximum allowable pressure on the pipeline is 100 m. Minimum pressure of transmission line, (–), = 3 m, William-Hazen coefficient, C is 100. (V = 0.85CR0 Josa ). Determine the diameter of pipeline, design WTL economically. Commercial Pipe Diameters: $200,250, 300,350, 400, 450, 500, 550, 600. 250m 162m (A) (3) 100m 50 V's/ (B) 1000 m 2000 m City 3000 m