Example ( 4-16) : The winch consists of a drum of radius ( 4 in. ), which is pie (B ) ( 3 in ). connected at its center ( C). At its outer rim is a ratchet gear having a mean radius of ( 6 in ). The pawl ( AB ) serves as a two-force member ( short link ) and keeps the drum from rotating. If the suspended load is ( 500 lb ), determine the horizontal and vertical components of reaction at the pin (C). 2 in 4 in.

Example ( 4-16) : The winch consists of a drum of radius ( 4 in. ), which is pie (B ) ( 3 in ). connected at its center ( C). At its outer rim is a ratchet gear having a mean radius of ( 6 in ). The pawl ( AB ) serves as a two-force member ( short link ) and keeps the drum from rotating. If the suspended load is ( 500 lb ), determine the horizontal and vertical components of reaction at the pin (C). 2 in 4 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Needs Complete typed solution with 100 % accuracy.
Requlred Information A countershaft carrying two V-belt pulleys Is shown In the figure. Pulley A recelves power from a motor through a belt with the belt tensions shown. The power Is transmitted through the shaft and dellivered to the belt on pulley B. Assume the belt tenslon on the loose side at B Is 15 percent of the tension on the tight side. Glven B(dg) = 400 mm, TA = 575 N, and TỊA2) = 3835.25 N. 300 450 400 TIA T(A2Y `150 250 dia. B(da) 20 dia. B At the point of maximum bending moment, determine the bending stress and the torslonal shear stress. The bending stress at the point of maximum bending moment is [.09515 MPа. The torslonal shear stress at the point of maximum bending moment is 259.442 MPа.
Iam reposting this question. Please solve it clearly
Learning Goal: To solve for the support reactions of a frame. The frame shown in (Figure 1) is supported by a pin at A and a pin at D. The two members are connected by a pin at C. The dimensions are H₁ = 1.1 m, H₂ = 1.3 m, and L = 1 m. The applied force P = 11 kN acts at the midpoint of BC, and the distributed load has intensity w = 1.3 kN/m. Figure H1 B A P O W H₂
subject: statics of rigid bodiesPlease be tidy and readable, as well as presenting your solutions.
two cylinders are connected to form a parallel cylinder actuatingsystem. Assume the bore and rod diameters of the left cylinder are 120 mm and 60 mm, respectively, and that those of the right cylinder are 100 mm and 50 mm. If the mass of the external loads to be driven by the left and right cylinders are 750 and 500 kg, respectively, and the back pressure in both rod-end chambers is 200 kPa, calculate the operating pressure of each cylinder for driving the loads. (Assume that the left cylinder requires 550 kPa for no-load extension and the right one requires 500 kPa.) If the supplying flow is 150 L ・ min−1, what are the extending velocities of those cylinders? Consider the friction and back pressure for the design Will those two cylinders extend simultaneously under the stated condition
Need help on all questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
A simple structure is to be built to hold load at C as shown in Figure Q5. Body ABC is pin joint at wall A is regarded as a rigid body and is pin supported to rod BD at B. The respective dimensions are as shown in the figure. A support unit is to be connected by pin between point B and point D or point D' at the wall. a) Compare and analyze the two positions for the support unit not to fail by buckling when maximum load F is applied at C. Which position is the better choice between D and D' ? b) If load F is in opposite direction, what is the maximum load F that can be applied. (Properties of rod BD, E= 200GPA, G=77 GPa, v=0.3, o, = 250 MPa ) A 1.6m В 1.4m C 0.9m F 10mm 4mm D 0.8m 9. 15mm mm D' Crossection of Hollow Rod BD or BD'. ( 10mm x 15mm and 4mm x 9mm) Figure 05
i need the answer quickly
B8
A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radii, r, = 0.0440 m and r, = 0.120 m, respectively. F A (a) If a downward force of F, = 16.0 N is applied to the end with the smaller radius, how much force F, would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) N (b) If the smaller piston is pushed down a distance d, = 0.208 m, through what distance d, would the other end move?
With Free Body diagram. Step by step Fast