Example 33:A thyristor used in a half wave rectifier used 220V, with firing angle 60°, totalresistance load 10 , inductance 5mH and frequency 60Hz , calculate:(a) load voltage and current (b) maximum direct voltage and current (c) normalizedvoltage and current (d) root mean square voltage and current and (f) power factor.

Answered: Image /qna-images/answer/4e477dc4-d600-4e41-80e4-f83a5b8f12d8.jpg

Example 33: A thyristor used in a half wave rectifier used 220V, with firing angle 60° , total resistance load 12 , inductance 5mH and frequency 60HZ , caleulate: (a) load voltage and current (b) maximum direct voltage and current (c) normalized voltage and current (d) root mean square voltage and current and (f) power factor.

Example 33: A thyristor used in a half wave rectifier used 220V, with firing angle 60° , total resistance load 12 , inductance 5mH and frequency 60HZ , caleulate: (a) load voltage and current (b) maximum direct voltage and current (c) normalized voltage and current (d) root mean square voltage and current and (f) power factor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the given Full Wave Center tapped Rectifier circuit, a step down transformer gives an RMS voltage as 110V/11-0-11 V is used with R₁ = 1 KQ. Assume diode as Germanium. D₁ a) Find Input Voltage Vin b) Find Peak Output Voltage. c) Find Average Output Voltage. d) Find Current through the load resistor. •ooooo 00000 CT 20-S D₂ R₁
A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: Peak to peak ripple voltage RMŞ ripple voltage 4. а.
A sine voltage trace displayed on a screen is shown in figure. The x axis is 1unit=40 ms and y axis is 1 unit=4 v; determine the frequency of the sine wave and plot the waveform if the same is applied to input of a full wave rectifier.
Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
A sinusoidal voltage wave form of peak voltage í V and frequency f = 60Hz is applied to a bridge rectifier and to half wave rectifier separately. The Differences of average values and output frequencies are
Q2) The expected average and RMS output voltage of the following PLECS circuit is equal to Single-phase diode rectifier L: 0.05 01 V_R (V i_N Scope V: 120 w: 2*pi*60 v_N R: 2.50 C: 500e-6 Oa) 40V, 84.85 V Ob) 38 V, 84.85V c) 38V, 80.2V O d) 40V, 38V Probe Probe
92) For three - phase half-wave Controlleed rectifier Shown in he figure: 1. Derive a fomu la for mean load Voltage. 2. praw the wave form of vo, i,,i, iy and voltage across thyristor 1 (r.) assuming highly inductive load and d = 120
Full wave rectifier normally produces A.unpredicted waveforms B.both polarities of input waveform to DC voltage C.positive phases of sinusoidal waveform D.pure sinusoidal waveform
Consider the full-wave bridge rectifier circuit. The input signal is 120 V (rms) at 60 Hz. The load resistance is R250. The peak output voltage is to be 9 V and the ripple voltage is to be no more than 5 percent. Determine the required turns ratio and the load current. Note: please solve within 30 minutes. Avoid plagiarism.
In half wave rectifier with filter, if the capacitance is increased, the ripple factor increases. True or false
Three Phase Uncontrolled Half Wave Rectifiers find the value of Voltage and Currents (output de and Root Mean Square) with all the proved, then sketch the curve from 0-2 on these axes (vs, vo, ia, ib, ic, io) explain its operation.
iii. For fully controlled single phase bridge rectifier with inductive load (load current is continuous) ,supply voltage 220 V(RMS) and a=30° .The mean value of output voltage is : (a) 150.32V (b) 171.52V (c) 120.98V