EXAMPLE 3.9 Compound roof trusses are used in a garden center, as shown in the photo. They have the dimensions and loading shown in Fig. 3-30a. Indicate how to analyze this truss. 1 kN 1 kN 1 kN 1 kN 1 kN 1 kN 1 kN 1 kN 3 de 1 kN 1 kN 0.5 kN M 1 kN 0.5 kN K A PC E a |H 30 30 F 6 kN 6 kN|1 m'1 m'1m'l m'1m'lm'1m'1m'lm'1m'lm'1m (a)

EXAMPLE 3.9 Compound roof trusses are used in a garden center, as shown in the photo. They have the dimensions and loading shown in Fig. 3-30a. Indicate how to analyze this truss. 1 kN 1 kN 1 kN 1 kN 1 kN 1 kN 1 kN 1 kN 3 de 1 kN 1 kN 0.5 kN M 1 kN 0.5 kN K A PC E a |H 30 30 F 6 kN 6 kN|1 m'1 m'1m'l m'1m'lm'1m'1m'lm'1m'lm'1m (a)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the degree of indeterminacy of the trusses as shown.
Problem 1 A beam is supported as shown below: A B F Hinge Hinge 5 m 5 m 6 m 3 m 3 m The beam is to carry the follov ving loads, in (kN) and in (kN/m), in the table below: LOAD W(DL) W(LL) P(LL) SET 1 (1,2,3,4,5) SET 2 (6,7,8,9,0) 20 25 40 30 15 50 Using influence line diagrams, determine the following: 2. Maximum reaction at F, RF in kN. ';
Please send me the question in 30 minutes it's very urgent plz
STRESSES 2. How many rivets are required to connect the boards together to form the beam, if the beam carries the loads shown in the figure. The shear capacity of each rivet is 50 IN BEAM KN. 75 mm 75 mm 20 KN 2.5 m 100 mm 20 KN/m 10 KN/m 2.5 m 20 KN/m 2 m 350 mm 100 mm ||
Current Attempt in Progress A simply supported timber beam with length L = 3 m carries a uniformly distributed load w = 11 kN/m. Determine the magnitude of the maximum compression bending stress that occurs in the beam at any location within the 3-m span length. 300 mm L 100 mm O 7.47 MPa O 5.18 MPa O 9.74 MPa O 8.25 MPa O 5.92 MPa Save for Later Attempts: 0 of 1 used Submit Answer
Concrete designs, third stage, civil engineering
A beam is supported as shown below: В C D E F Hinge Hinge 米 5 m 5 m 6 m 3 m 3 m The beam is to carry the following loads, in (kN) and in (kN/m), in the table below: LOAD w(DL) W(LL) P(LL) SET 1 (1,2,3,4,5) SET 2 (6,7,8,9,0) 20 25 40 30 15 50 Using influence line diagrams, determine the following: 2. Maximum reaction at F, RF in kN.'
The ward floor of a certain hospital has the plan shown. Question: Determine the dead load due to its weight of beam AD if it is made up of concrete with 0.25mx0.45m cross section.
Q. For the figures shown; 1. Draw S.F. & B.M. diagrams 2. Determine the maximum bending and shearing stresses developed in the beam. 1. Ans. : (o)max= 378 MN/m (t)max = 39 MN/m? 60 KN 1m |30 KN 5 KN/m 58 102 4m 2m Beam cross-section 2. Ans. : (o)max= 288 MN/m2 (t)max = 3.6 MN/m? 1500 N/M 25mm B A 6 m 3 m Beam cross-section 3. Ans. : (olmax = 94.7 MN/m? (t)max = 3.5 MN/m? | 20 KN 150mm 4 KN/m A 100mm 4m 4m 2m Beam cross-section 150mm 100mm 200mm B.
Please identify the member forces used in the illustration for Question No. 1. Indicate whether the tension or compression is wanted.