Example 23.19. A concentric spring for an aircraft engine valve is to exert a maximum force of 5000 N under an axial deflection of 40 mm. Both the springs have same free length, same solid length and are subjected to equal maximum shear stress of 850 MPa. If the spring index for both the springs is 6, find (a) the load shared by each spring, (b) the main dimensions of both the springs, and (c) the number of active coils in each spring. Assume G = 80 kN/mm² and diametral clearance to be equal to the difference between the wire diameters.

Example 23.19. A concentric spring for an aircraft engine valve is to exert a maximum force of 5000 N under an axial deflection of 40 mm. Both the springs have same free length, same solid length and are subjected to equal maximum shear stress of 850 MPa. If the spring index for both the springs is 6, find (a) the load shared by each spring, (b) the main dimensions of both the springs, and (c) the number of active coils in each spring. Assume G = 80 kN/mm² and diametral clearance to be equal to the difference between the wire diameters.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PLEASE ANSWER ALL OF THIS QUESTION ASAP!!!
Q3. Design a compressive helical spring which was made of alloy steel. The maximum applied load to the spring is 1000 N. The total number of the coils should be no more than 10 turns if a squared and ground ends spring used. The solid length is 60 mm. Neglecting the effect of stress concentration. What is (1) the energy stored in the spring. (2) axial deflection. (3) The mean diameter of coil. (4) The wire diameter. (5) Spring rate. If the applied load is shifted to the edge of the spring, farthest point from the centre of the spring, determine the load that the spring can carry it without failure.
A helical compression spring is wound using 4 mm-diameter Chrome-vanadium wire. The spring has an outside diameter of 28 mm with squared and ground ends, and 14 total coils: (a) What should the free length be to ensure that when the spring is compressed solid the torsional stress does not exceed the yield strength, that is, that it is solid-safe? (b) What force is needed to compress this spring to closure? (c) Estimate the spring rate. (d ) Is there a possibility that the spring might buckle in service?
Spring stiffness is important as it is the measurement of the resistance offered by the elastic body to deform as such state TWO effects of spring stiffness in a helical compression springs when its original length is cut into half.
A steel helical compression spring of an average coil diameter of 16 mm with a wire diameter of 1,4 mm and active coils of 6. Assuming Gsteel as 80 GPa, predict (a) the axial load (b) the deflection (c) spring rate
A closely coiled helical spring is made of 6 mm diameter steel wire, the mean diameter of the coil is 60 mm and there are 8 coils. Taking the modulus of rigidity as 100 kN/mm2, find the stress, in kPa, in the wire when carrying an axial load of 529N.
None
Two concentric springs are constructed with squared and ground ends from oil-hardened steel. The ultimate strength for the steel is 204,000 lbf/in². The steel's yield strength is to be estimated as 75% of the ultimate strength. The shear modulus for the steel is 11.5 x 106 lbf/in². The springs support a static force of 150 lbf. The spring dimensions and properties are as follows: Inner spring Wire diameter: 0.177 in Mean coil diameter: 1.5 in Total number of coils: 12.75 Free length: 4.5 in Outer spring Mean coil diameter: 2.0 in Wire diameter: 0.2253 in Free length: 3.75 in Total number of coils: 10.25 1. The deflection of the inner spring is most nearly A. 2.0 in B. 2.4 in C. 2.9 in D. 3.1 in 2.The maximum force exerted by the inner spring is most nearly A. 57 lbf B. 67 lbf C. 79 lbf D. 86 lbf 3. The maximum shear stress in the inner spring is most nearly A. 47 kips/in² B. 52 kips/in² C. 57 kips/in² D. 64 kips/in² 4. The factor of safety in shear for the inner spring is most nearly…
A steel helical compression spring of an average coil diameter of 16 mm with a wire diameter of 1,4 mm and active coils of 6. Assuming Gsteel as 80 GPa, predict (a) the axial load (b) the deflection (c) spring rate
(10) A weight of 270kg falls a distance of 1.0m & strikes a coil compression spring which absorbs the blow with a deflection of 0.3m. The mean diameter of the coils is to be 8x the wire diameter. If the allowable stress is 415MPa & the modulus of rigidity is 80GPa, find the diameter of the wire & the number of effective coils required.
A petrol engine inlet valve is spring-loaded. The valve opens at 360 N closes at 220 N, while the corresponding lengths of springs when it is open is 41 mm and when it is closed is 49 mm. The maximum inside diameter of the spring is 25 mm. Assume the shear yield strength in steel as 400 MPa, shear ultimate strength is 643.2 MPa and shear modulus as 80 kN/mm². Assume the helical compression spring has squared and ground ends, minimum factor of safety, n = 1.5 and spring index, C = 5. Determine for shot-peened wires a) initial compression b) coil diameter d using Zimmerli data, Goodman theory and Langer theory. Select standard size of Washburn & Moen wire c) helical diameter D d) number of actual turns, Na and total turns, Nt e) free length
(13) A spring has an overall length of 44.0in & sustains a load of 15,000lb @ its center. The spring has three full-length leaves & 15 graduated leaves with a central band 4.0in wide. All leaves are to be stressed to 60,000psi when fully loaded. The ratio of total spring depth to width is to be approximately 2.0. Determine: (a) the width & thick ness of the leaves; (b) the initial space that must be provided between the full length & the graduated leaves before the band is applied; (c) What load is exerted on the band after the spring is assembled?