Example 21.6. A hydraulic accumulator has sliding ram of 400 mm diameter which slides rough 7-5 m in 3 minutes during its working stroke, while weight on the ram including its self ght is equivalent to 300 kN. The pump supplies water at 0.009 m³/s rate and packing friction ats to 4 percent of total load. Determine: (Pressure intensity of water, Power delivered to machine supplied by accumulator, Power required to drive the pump having efficiency 72 percent. C Li

Example 21.6. A hydraulic accumulator has sliding ram of 400 mm diameter which slides rough 7-5 m in 3 minutes during its working stroke, while weight on the ram including its self ght is equivalent to 300 kN. The pump supplies water at 0.009 m³/s rate and packing friction ats to 4 percent of total load. Determine: (Pressure intensity of water, Power delivered to machine supplied by accumulator, Power required to drive the pump having efficiency 72 percent. C Li

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An idelaized centrifugal pump, data given as follows; Blade outer radius of blade = 30 mm Power = 1 KW - Running speed = 1000 rpm Entry of liquid into the pump is axial and exit from the pump is radial with respect to impeller. Determine the mass fow rate of the liquid through the pump?
A volute centrifugal pump has the following performance data at the best efficiency point: volumetric flow rate Q-0.015 m's Ah - 65 m total head required net positive suction head NPSH- 16 m liquid power impeller speed impeller diameter Evaluate the performance of an homologous pump which operates at an impeller speed of 29.2 rev/s but which develops the same total head Ah and requires the same NPSH. PE- 14000 W N= 58.4 revis D-0.22 m
The 28-in-diameter pump in Fig. 11.7a at 1170 r/min is used to pump water at 20°C_through a piping system at 14,000 gal/min. (a) Determine the required brake horse- power. The average friction factor is 0.018. (b) If there is 65 ft of 12-in-diameter pipe upstream of the pump, how far below the surface should the pump inlet be placed to avoid cavitation?
A centrifugal purmp is used to lift water from a water reservoir with level 2 m below the pump center line. Then, to another reservoir with level 7 m above the center line. Pressure gages readings from the suction and discharge are 1 bar and 4 bars respectively. The flow rate at 0.74 m /s with pipe inside diameters of 400 mm at suction and 250 mm at the discharge. Assume over all head loss due to friction of 4 J/N, what is the water power in kW?
19. A centrifugal pump delivering 0 04 cumec of water to a height of 20 metres through a 10 cm diameter pipe 100 metres long. If the overall efficiency of the pump is 75% find the h.p. required to drive the pump. Take f 0'01. (51'83 hp)
C3 (1). A single-acting reciprocating pump has a bore of 162 mm and a stroke of 350 mm. When the pump runs at 54 rpm, it discharges 3.9 liters per second under a total head of 16 m. Determine (i) the theoretical discharge in m/s (i). the actual power required in Watts, (i) the coefficient of discharge and (iv) the delivery head, if the suction head is 4.8 m. Take the density of water= 1000kg/m g=9.81 m/s?
When designing an impeller for a centrifugal pump, you would consider the following materials attributes. [M ten waaler vir 'n sentrifugale pomp ontwerp, sal jy die volgende materiaal eienskappe in ag neem.] O A. creep strength and density O B. hardness and chemical composition O C. toughness and stiffness O D. hardness and thermal expansion
A pump with an impeller diameter of 0.02 m, a total capacity of 12 L/s, an impeller speed of 58.3 rpm, an available head of 70m, and a brakepower of 12kW is used to pump water. Calculate the capacity of a homologous pump with twice the impeller diameter and operating at half the speed.
Q.2 A centrifugal pump is required to pump water to an open water tank situated 4 km away from the location of the pump through a pipe f diameter 0.2 m having Darcy's frřiction factor of 0.01. The average speed of waterinthe pipe is 2 m/s. If it is to maintain a constant heac of 5 m in the tank, neglecting other minor losses, the absolute discharge pressure at the pump exit is (a) 0.449 bar (c) 44.911 bar dund (b) 5.503 bar (d) 55.203 bar