EXAMPLE (2) A bar of uniform cross sectional area 100mm2 is subjected to forces as shown in Fig . Calculate change in length of the bar. Take E=2*10 N/mm?. А В C D 1kN 5KN →6KN 2kN 300mm 400mm 600mm

EXAMPLE (2) A bar of uniform cross sectional area 100mm2 is subjected to forces as shown in Fig . Calculate change in length of the bar. Take E=2*10 N/mm?. А В C D 1kN 5KN →6KN 2kN 300mm 400mm 600mm

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 28P

See similar textbooks

Related questions

Q: EXAMPLE (2) A bar of uniform cross sectional area 100mm2 is subjected to forces as shown in Fig.…

Q: Determine the stiffness of the string shown below given that the natural frequency of the system is…

Q: A rigid bar AB is supported by a spring as shown in the figure above. What is the deflection of the…

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

Q: Problem 2: For the following cross-section, compute l assuming the centroid of the entire cross…

A: It is asked to compute the Moment of Inertia, Ix for the given cross section Given centroid of the…

Q: 40 kN/m 15 KN/m 600 mm GOomm 600 mm

Q: For the section shown, calculate the moment of inertia about the X-ахis:

Q: Example : Replace the three forces acting on the bent beam by a single equivalent force R. Specify…

Q: ID t X< Compute the area moment of intertia about the x and y axes shown in the figure (the origin…

Q: EXAMPLE (2) A bar of uniform cross sectional area 100mm2 is subjected to forces as shown in Fig .…

Q: Two L 152x102x12.7 angle brackets are welded to a steel plate that is 16 cm tall and has a width d…

A: The given data is shown below: L152×102×12.7Height=16 cmIxIy=1.5

Q: Calculate the value of the integration constant C4. Enter your answer in kNm2 to three decimal…

A: Given:a=b= 5mq= 5kN/mRequired:Value of integration constant C4

Q: A cylinder with a weight of 800 lb is held in equilibrium by three ropes. The hooks are arranged in…

Q: Consider the cross section shown in (Figure 1).Suppose that b = 118 mm Determine the major principal…

A: Given : b = 118 mm To Find :

Q: From the given figure below, determine the distance of the centroid from the y-axis, in mm. 13mm mm…

Q: (Figure 1) Figure 30 mm 140 mm. 30 mm 30 mm 70 mm 30 mm 170 mm 1 of 1 > ▼ Part A Determine the…

A: to find the centroid of the area about its left edge and the moment of inertia about its vertical…

Q: The two forces are equivalent to a force R that has a line of action pass through point A. Determine…

Q: Yg Z.. 200 mm ly G 20 mm 20 mm 200 mm

Q: Example : Replace the three forces acting on the bent beam by a single equivalent force R. Specify…

Q: For the shape below, assume the following dimensions: a = 175 mm b = 220 mm d = 300 mm t = 23 mm The…

A: Given:Required :Moment of inertia along centroidal y axis

Q: A bar of uniform cross sectional area 100mm2 is subjected to forces as shown in Fig. Calculate…

A: Given Cross sectional Area = 100 mm2 E= 2 x 105 N/mm2 Forces and diagram To find Total deflection…

Q: For the frame shown below, The mass of the object connected is 60-kg. what is the value of…

Q: 150 mm (5) 150 mm 1000 mm A, = 8622 uu OSI- unU ŞLS 650mm

A: Width ( b) = 150+150=300mm Effective depth = 575mm Factor of safety for steel =1.15 Factor of safety…

Q: 25 cm 2.5 cm 15 cm 2.5 cm

A: solution first find the centroid distance with respect to base consider T-section as two figures 1.…

Q: EXAMPLE (2) A bar of uniform cross sectional area 100mm2 is subjected to forces as shown in Fig.…

A: Given Cross sectional area,A=100mm2 E=2×105MPa

Q: Determine the slope at point B of the beam in the figure below. Assume the material's modulus of…

Q: The cross-section of a built-up steel column is given in the figure. Calculate the value of the…

A: From section properties table, Moment of inertia of I 300 about its centroid = 8603.60 cm4 Centroid…

Q: The object W1 in the figure is at an angle of 45 to the horizontal It is based on its frictionless…

Q: Verify the given moment(s) of inertia and find x and ÿ. Assume that each lamina has a density of p =…

A: Given diagram:-

Concept explainers

Friction

Friction is defined as the force that prevents any solid surface, any layer of fluid, or any kind of element or material from sliding.

Question

EXAMPLE (2)
A bar of uniform cross sectional area 100mm2 is subjected to forces as shown in
Fig . Calculate change in length of the bar. Take E=2*10 N/mm?.
A
В
C
D
1kN
5KN
→6KN
2kN
300mm
400mm
600mm
to

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Start Siide Show B Print to PDF Commer • 1. a. How far does a particle travel between zero to four seconds if its position is given by: S (t) = t4 8t2 ( ft) Note use time intervals 0→2 and 2→4 b. Find the acceleration when velocity is zero C. Find the average velocity at t = 1s and t = 3 s %3D d. Find the average acceleration att = 0 andt = 2 s
THE CENTROID OF THE PLANE REGION IS LOCATED AT C. IF THE AREA OF THE REGION IS 20OOMM2 AND ITS MOMENT OF INERTIA ABOUT THE X- AXIS IS IX =40 x 106 MM4, DETERMINE IU. dz = 70 mm Ce d = 90 mm DETERMINE lu (Unit: mm^4) Your answer Back Next Clear form
Express F as a vector in terms of the unit vectors i, j, and k. Determine the angle between Fand the positive y-axis. Assume r, = 35 mm, ry = 60 mm, r, = 175 mm, F = 50 N. %3D Dimensions in millimeters No need to attach your solution.use the box to input your answer. Answer 9 * (1) в I х, >
Need correctly in proper handwriting.
Solve it early
A=0 and B=4 Question at the photo.
Q3: Consider a two degree of freedom bar elements as shown in figure. Using finite element method to formulate the equilibrium equation of it. If the cross sectional area is 10 mm² and E=100 GN/m². | 20KN – 30KN ISKN - 300 -600–+ 350 All Dimension in mm
Move the resultant of the forces acting on the bar in the figure to point O and calculate the straightening angles. . Select a value so that the distance X is between 5 ≤ X ≤ 9.
Compute the coordinates of the centroid (1,7) of the area shown. Also compute the area moment of intertia about the z' and y' axes with origin at the centroid. лу b с d h W. 3 พ kd→ b Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 14 mm 113 mm 18 mm 49 mm 99 mm 14 mm The z coordinate of the centroid is 2013 Michael Swanbom cc) 130 BY NC SA = mm. a h The y coordinate of the centroid is The moment of inertia about the z' axis going through the centroid is IT The moment of inertia about the y' axis going through the centroid is I mm. mm¹. mm4.
(a)The force acting on a particle varies as in the shown figure. Find the work done by the force on the particle as it moves (a) from x-0 to x= 8 m,(b) from x-8m to x= 10m.c) from x=0 to x-10. F(N) 4 x(m) 2 46 8 10 -2
Compute the coordinates of the centroid (,) of the area shown. Also compute the area moment of intertia about the # and y axes shown in the figure and the z' and y' axes with origin at the centroid. y a b c y = a√bx Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 4.5 in 1.2 in¹ (Note the -1 exponent only applies to the unit, not the number.) 9 in coordinate of the centroid is The The y coordinate of the centroid is The moment of inertia about the z axis is Iz in4. in4. The moment of inertia about the y axis is Iy The moment of inertia about the z' axis going through the centroid is IT' The moment of inertia about the y' axis going through the centroid is ly in. Xx in. Cc+❀O BY NC SA 2016 Eric Davishahl in4. in4.
Find the centroid of the figure below.