Example 18.1. A short C.I. column of hollow circular section is attached with a projection bracket carrying a load of 100 kN. The load line is off the axis of the column by 200 mm. Find the maximum and minimum stress intensities in the column if it has an external diameter of 200 mm and internal diameter of 150 mm.

Example 18.1. A short C.I. column of hollow circular section is attached with a projection bracket carrying a load of 100 kN. The load line is off the axis of the column by 200 mm. Find the maximum and minimum stress intensities in the column if it has an external diameter of 200 mm and internal diameter of 150 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PLASE FULL ANSWER. DON'T COPY FROM OTHER ONLINE ANSWERS
Two cable support a block of weight W as shown, given the cross-sectional area for AB as 650 mm? and for AC as 475 mm2. Calculate the maximum safe load of W if the stress is limited for 100 MPa for the both cable. 60 40 W
* Required For nos. 38-40, satisfy the conditions of the given problem below: The internal drag truss of the wing of a light airplane is subjected to the forces shown in Determine the force in figure 3. each member, and state if the members are in tension or compression. 38. Load on member BC * 1 point H 0.61 m 0.61 m- 0.61 m 356 N O A. 579.23 N (T) B. 579.32 (C) O C. 580.20 N(T) D. 580.20 N (C) 356 N 0.61 m -0.46 m- 267 N 178 N
II. A post tapers uniformly from a diameter d at the upper end to a larger diameter D at the lower end, as shown. It supports an axial load of P. Given allowable stress of S, the post's dimension can be determined using the formula o=P/A. For structural safety, what must be the area in this formula? The lower, middle, or upper cross- section of the post? Why? Upper Area Middle Area Lower Area
Ql- Compare the maximum stress induced into a rectangular plate 100mm long into x-axis direction, 50mm width into y-axis direction and 10mm thickness into z-axis direction is subjected to tensile load of 10kN into y-axis direction for bellow cases: 1- As a solid plate. 2- The same plate with a Circle hole 10mm diameter in xy-plane in the center the plate.
A steel column of hollow circular cross section shown in Figure is supported on a circular steel base plate and concrete pedestal The column has outside diameter 220 mm and a wall thickness of 15 mm. It supports an axial load of 680 kN.a. Determine the bearing stress induced by the column to the base plate in MPa.b. If the allowable bearing stress on the pedestal is 10MPa, determine the required diameter of the base plate in mm.
3. Calculate the critical load of a strut which is made of a bar, circular in section and 5 m long and wheh is pin-jointed at both ends. The same bar when freely supports gives mid-span deflection of 15 mm with a load of 85 N at the center.
A round cast iron column 5m long and 299mm ...
6.10 - This is a statics problem that deals with ‘Zero-Force Members’.
I neeed typing clear
4. The bar below is subjected to an axial load of P. The safety factor against compressive failure is 1.5. Find the allowable load in KIPS if the material is cast iron. Sin 2in 1 ft
Example 2.20 1.5 m 5 m 1.5 m 10 kN ": ;. A concrete structure is subjected to a 10 kN downward load. Determine the load on the columns. ĮskN skN M-5* 1-5 = 7.5*. m 1.5m skN 7,5 kN. m SKE110 INTRODUCTION TO STRUCTURES 32