Examining and modifying the contents of the 80O86's internal registers1. Use the REGISTER command to display the current contents of all the internal registers bytyping R.o List the values of the following regasters.o What is the address of the next instruction to be executed2. Enter the command. RAll chit CR) What happens and why?3. Use a REGISTER commund to first display the current contents of BX and then change thisvalue to 0020h.

Answered: Image /qna-images/answer/01c1596a-bef1-4763-b1b7-dcb5c0d6c622.jpg

Examining and modifying the contents of the S086's internal registers 1. Use the REGISTER command to display the current contents of all the internal registers by typing R. o List the values of the following registers 71 o What is the address of the next instruction to be executed? 2. Enter the command. R All chit CR) What happens and why? 3. Use a REGISTER command to first desplay the current contents of BX and then change this value to 0020h.

Examining and modifying the contents of the S086's internal registers 1. Use the REGISTER command to display the current contents of all the internal registers by typing R. o List the values of the following registers 71 o What is the address of the next instruction to be executed? 2. Enter the command. R All chit CR) What happens and why? 3. Use a REGISTER command to first desplay the current contents of BX and then change this value to 0020h.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

When using a branch instruction, the lowest two bits in the offset to add to the $pc can bedropped.a) Why can these two bits be dropped?b) What must happen when the branch address is later calculated?c) Do you think the lowest two bits can be dropped in the absolute address for a jumpinstruction? Why or why not?
kindly answer! NEED ASAP IN 15 MINUTES! MCU IS ATMEGA328P
Examining and modifying the contents of the 8086's internal registers 1. Use the REGISTER command to display the current contents of all the internal registers by typing R. o List the values of the following registers: AN SP BX DS DX SS IP ES o What is the address of the next instruction to be executed? 2. Enter the command: R AH (hit ) What happens and why? 3. Use a REGISTER command to first display the current contents of BX and then change this value to 0020h.
8. If BX contains 5474H, what is the value in BX after the following instruction? ADD BH, BL 9. Show the instructions needed to divide (unsigned) AX by 7. Where the remainder is stored? 10. Write the appropriate or instruction to reset bits 5 and 7 of register AX, and keep all others unchanged. 11. Write directive to allocate 10 bytes in memory. 12. What EQU directive is used for?
Answer it properly
Q4: By using assembly language instructions, write suitable statements to execute the following (Choose Three Only) 1. Clear the DX register with just one instruction. 2. Clear the odd numbers of AX register with just one instruction. 3. Divide 4482H by 16H and put the quotient in the BX register (Without using Division instruction). 4. Save the flags contents to BL register.
amining and modifying the contents of the 8086's internal registers 1. Use the REGISTER command to display the current contents of all the internal registers by typing R. o List the values of the following registers: o What is the address of the next instruction to be executed? 2. Enter the command. R All (hit CR>) What happens and why? 3. Use a REGISTER command to first display the current contents of BX and then change this value to 0020h.
Let's say you needed a procedure to return to a memory address that was 3 bytes higher than the one on the stack right now. Create a set of instructions that will be put shortly before the RET instruction in the function to complete this job.