The method of dimensions,

Q: Determine the area of cross-section.

A:

Q: 3.0 A uniform horizontal 300.0 N beam, 5.00 m long, is attached to a wall by a pin connection that…

A:

Q: Meaning of scale in measurement

A: scale is used to show the actual dimensions that exist in a drawing sheet. you can clearly…

Q: and right embankments are 11 and 13 kN/m³, respectively. Determine the stress increase Two…

A:

Q: Q1): A field book is reproduced below in which some readings marked as (x), are missing. The true…

A: We have to determine the complete all missing data and perform all asthmatic checks and compute…

Q: Determine the Vertical Deflection at the hinge E- 29x103 ksi = 80 in 4 5 k internal hinge 1.2I 3'

A:

Q: What is the most common scale used for temperature

A: The Celsius and fahrenheit scale is used most commonly used.. Kelvin scale is primarily used in…

Q: Find the centroid of the following cross-sections and planes.

A: Centrodal distanceX = 5.333 inY = 5.667 inExplanation:Step 1:Step 2:

Q: Why should a figured dimension be used in preference to a dimension scaled off a drawing?

A: Figured dimension is used in preference to a dimension scale because:

Q: Calculate the volume between the two cross sections below. KM1+850 17 m2 23 m2 KM 2+050 10 m2 4 m2

A: From the given cross section we can sayAt station 1+850 and Area cut cm2| 17+23 = 402+050   End Area…

Q: What is e sub 0 referring to?

A:

Q: Draw the 3 Principal Views of the object (given unit in mm, convert it to cm) 51 35 15 25 53 73 20…

A: 3D view of the object is provided. We have to draw three principal views of the object.  Three…

Q: The drag racer P starts from rest at the start line S and then accelerates along the track. When it…

A:

Q: How is unit weight expressed in primary dimensions?

A: Unit Weight is defined as the Weight of soil per unit volume.

Q: Problem 4 A thin-walled cylindrical pressure vessel has an internal diameter of d = 2 m and a wall…

A:

Q: The ends of the triangular plate are subjected to three couples. Determine the magnitude of the…

A: Given:-  The ends of the triangular plate are subjected to three couples. Determine the magnitude of…

Q: 75 mm 50 mm The compound shaft is attached to a rigid wall at each end. For the bronze segment AB,…

A:

Q: 4. The driver of a vehicle on a level road determined that she could increase her speed from rest to…

A: Speed increased from rest to 50 mph in 34.8 secSpeed increased from rest to 65 mph in 94.8…

Q: How are units converted using dimensional analysis?

A:

Q: Q2) It is required to measure the distance from A to C which was obstructed by a building (see the…

A:

Q: If the actual dimension is 46 m and the scaled dimension is 184 cm, what is the scale used?

A:

Q: Convert the equivalence scale 1 inch = 30 feet to a ratio scale.

A: Solution:- Scale:- The scale of the map is the ratio of a distance on the map to the corresponding…

Q: diagrams

A:

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5…

A:

Q: Lo to op- P2.6-7 kN, as shown in Fig. P2.6-7. If the steel has a modulus of elas- ticity E = 200 GPa…

A: We have to determine the value of change in length of the column and the change in the thickness of…

Q: Mechanics

A:

Q: Replace the loading acting on the beam by a single resultant force. Specify where the force acts,…

A: To find Single resultant force, Fr and the location where it is acting, d

Q: Value the line theorem in the context of scale drawing.

A: Scale drawing: In the scale drawing, an object has exactly the same shape as the original object but…

Q: 5. An elastomeric bearing pad consisting of two steel plates bonded to a chloroprene elastomer (an…

A: Given  Dimensions a= 125 mm  b= 240 mm  t= 50 mm  Shear force, V= 12 KN

Q: 17" IROH 6" SIBAR 8" 2" 003 al a 1" (Typ.) don 10 5682 2074 Philos 12" mixa si stalupio of beau…

A:

Q: Correctly Dimension the object using datum dimensioning

A: To show the datum referencing of the drawing

Q: Question 1) Determine the x and z components of reaction at the journal bearing A and the tension in…

A: F1 = -800 k F2 = 350 j

Q: "dimensional modelling."

A: Answer : Data provided : term "dimensional modelling."   To determine : concept of dimensional…

Q: Define matrix's diagonal, off-diagonal, subdiagonal, and superdiagonal elements. Illustrate each.

A: An n×n matrix, or a matrix with the same number of columns as rows, is known as a square matrix.

Q: An L-shaped bracket is fastened to the wall (x-z plane) at points A and B and extends out parallel…

A: Given: A L shaped bracket with 200 N force acting at C  Required: Moment at point A in vector form…

Q: Find the centroid of the following cross-sections and planes.

A: Centroid is = (0, 9.427 in)Explanation:Step 1: Calculation for centroid of given section.Thanks.

Q: Define: First Moment of Area Sketch Or Drawing: Equation: Units:

A:

Q: Find the centroid of X and Y in tabular form.

A: A centroid is a point on the body on which the mass of a body is uniformly distributed. If the body…

Q: Can you please redo this and explain how you got what you got? I dont understand concept and show…

A: To draw a cross-section AA' and BB' for the given section.

Q: STRUCTURAL MEMBERS SLAB B (m) 8 8 5.3 4.5 4 Slab 1 Slab 2 Slab 3 Slab 4 Slab 5 BEAMS Grid A Grid B…

A:

Quantity takeoff

Quantity takeoffs (QTO) are precise estimates of the materials and labor costs required to finish a construction project. During the pre-construction phase, an estimator prepares them, breaking down the project into smaller, more manageable parts that are easier to evaluate. These measurements are used to prepare a construction scope bid. Estimators examine the drawings, specifications, and models to figure out different quantities and their costs. Since, the components, their quantity, and price are all included in the model, quantity take-off can be done automatically using Building Information Modelling (BIM). The time taken for completing a construction project can be reduced by the use of quantity takeoff. These takeoffs are also called material takeoffs and construction takeoffs.