Answered: Ex 12 : Calculate the work done in… | bartleby

Related questions

Question

Ex 12 : Calculate the work done in blowing a
soap bubble of radius 0.5 cm. Surface tension
of soap solution is 2.5 x 10-³ N/m.

Expert Solution

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

(50%) Problem 2: Suppose the maximum blood pressure for a specific person is 155 mm Hg. Calculate the maximum force, in newtons, exerted by the blood on an aneurysm (a ballooning in a major artery), given that the effective area of the aneurysm is 22.5 cm². Grade Summary F = | Deductions 0% Potential 100% sin() cos() tan() 7 8 9 Submissions НOME Attempts remaining: 10 (2% per attempt) detailed view cotan() asin() acos() E A| 4 5 atan() acotan() sinh() 1 2 3 cosh() tanh() cotanh() + END O Degrees Radians VO BACKSPACE DEL CLEAR Submit Hint Feedback I give up! Hints: 0% deduction per hint. Hints remaining: 1 Feedback: 0% deduction per feedback.
9. ssm When a .22-caliber rifle is fired, the expanding gas from the burn- ing gunpowder creates a pressure behind the bullet. This pressure causes the force that pushes the bullet through the barrel. The barrel has a length of 0.61 m and an opening whose radius is 2.8 × 10-³ m. A bullet (mass = 2.6 X 10-³ kg) has a speed of 370 m/s after passing through this barrel. Ignore friction and determine the average pressure of the expand- ing gas.
When a .22-caliber rifle is fired, the expanding gas from the burning gunpowder creates a pressure behind the bullet. This pressure causes the force that pushes the bullet through the barrel. Suppose the barrel has a length of 0.633 m and an opening whose radius is 2.67 x 10-3 m. A bullet (mass = 2.6 x 10-3 kg) has a speed of 348 m/s after passing through this barrel. Ignore friction and determine the average pressure of the expanding gas.
A hand-driven tire pump has a piston with a 3.00 cm diameter and a maximum stroke of 35.0 cm. (a) How much work (in J) do you do in one stroke if the average gauge pressure is 2.40 x 105 N/m2 (about 35 psi)? (b) What average force (in N) do you exert on the piston, neglecting friction and gravity? N
24. A hot air balloon with a mass of 700kg ascends at a constant rate of 1.60m/s for 20.0s. Howmuch work is done by the upward buoyant force? (Neglect air resistance)a. 250,000 Jb. 189,160 Jc. 220,000 Jd. 188.000 J
A hand-driven tire pump has a piston with a 2.00 cm diameter and a maximum stroke of 29.0 cm. (a) How much work (in J) do you do in one stroke if the average gauge pressure is 2.40 ✕ 105 N/m2 (about 35 psi)? (b)What average force (in N) do you exert on the piston, neglecting friction and gravity?
How much work (in J) must be done to inflate the balloon when the atmospheric pressure is 1.0 bar and the volume of the hot-air balloon is 16.1 m3 when inflated.
Problem 9 A boxcar of length 9.9 m and height 2.4 M is at rest on frictionless rails. Inside the boxcar (whose mass when empty is 3000 kg) a tank containing 1700 kg of water is located at the left end. The tank is 1.1 m long and 2.4 m tall. At some point the walls of the tank start to leak, and the water fills the floor of the boxcar uniformly. Assume that all the water stays in the boxcar. After all the water has leaked out what will be the final velocity of the boxcar? (Take movement to the right as positive. Assume that the mass of the boxcar is evenly distributed.) Submit Answer Tries 0/8 What is the displacement of the boxcar 6 S after the water has settled in the bottom. (Take positive displacement as being to the right.) Submit Answer Tries 0/8
An 210kg drone hits the ground at 311km/h and penetrates to a depth of 81.0cm.What was the force the ground exerted on the drone?
Homework 4 Problem 2: A hand-driven tire pump has a piston with a 2.8 cm diameter and a maximum stroke of 24 cm. Part (a) How much work do you do in one stroke if the average gauge pressure is 2.4 × 105 N/m2? W = ______ Part (b) What average force do you exert on the piston, neglecting friction and gravitational force? F = ______
When gasoline is burned in the cylinder of an engine, it creates a high pressure that pushes on the piston. If the pressure is 150 pound-force per square inch [psi], and it moves the 4-inch [in] diameter piston a distance of 4 centimeters [cm] in 0.2 seconds [s], how much horsepower [hp] does this action produce? Click the icon to view the conversion table. Click the icon to view the table of common derived units in the SI system. ..... The power is 0.01 hp. (Round your answer to two decimal places.)
A cylinder is fitted with a piston, beneath which is a spring, as in the drawing. The cylinder is open to the air at the top. Friction is absent. The spring constant of the spring is 330O N/m. The piston has a negligible mass and a radius of 0.034 m. (a) When the air beneath the piston is completely pumped out, how much does the atmospheric pressure cause the spring to compress? (b) How much work does the atmospheric pressure do in compressing the spring? H So e (a) Number i Units (b) Number i Units > >

SEE MORE QUESTIONS