euguA 80hN GUKN 30 SOKN TERnd a ond f

Q: (2) A two-stage cascade refrigeration system uses ammonia as the refrigerant. The mass flow rate in…

A: According to the given data the mass flow rate in the high-pressure loop = 0.10 kg/s The condenser…

Q: The figure below shows the S-N curve of three materials subjected to cyclic fatigue about a mean…

A:

Q: Liquid cooling system is advantageous because: Select one: a. It requires many components (pump,…

A: Option b is correct  Because liquid have high conductivity than air so it will be remove heat at…

Q: Q.2 Draw the Shear Force Diagram and Bending Moment Diagram for the beam shown in Figure 2, where R…

A:

Q: The velocity of a particle moving in the x-y plane is given by (7.82i +3.51j) m/s at time t = 3.15…

A: Given:To find:

Q: Determine the z-coordinate of the mass center of the homogeneous paraboloid of revolution shown. 4…

A: Given  Radius is 4 in  Height is 10 in  Required: mass centre

Q: The sides AB and CD of a quadrilate 2. ABCD are extended to points P and respectively. Is ZADQ+ ZCBP…

A: Following are some standard geometrical figure 1) Triangle 2) Rectangle 3) Circle 4) Quadrilateral A…

Q: Two individuals are attempting to relocate a sofa by applying forces in the indicated directions. If…

A:

Q: By direct integration, determine the moments of inertia of the triangular area about the x- and…

A: Given: There is a triangular plate with height 13 inch side along x' axis is 6 inch. For finding…

Q: Determine the magnitude and location of the equivalent hydrostatic force acting on the circular gate…

A:

Q: PROBLEM 5: The water in a tank is pressurized by air, and the pressure is measured by a multifluid…

A:

Q: Q2. A. Given is 1 hr-UH for a certain catchment. Derive the 2hr.-UH I hr.-UH (1-mm) for the…

A:

Q: The deceleration of the truck The stopping distances Time needed to stop the truck 2

A: Given: u= 90 km/h Braking force=6900 N m=2300 kg v=0 To determine: Deceleration of the truck Time to…

Q: Dimensions in mm Determine the magnitude of the force (in N) of the x-component of the internal pin…

A:

Q: A piezoelectric type accelerometer has a sensitivity of 100 mV/g. The transducer is subjected to a…

A:

Q: 30 mm 150 mm y 30 mm 150 mm The moment of inertia (in mm) about the axis of symmetry is nearest?

A:

Q: (1) A two-stage cascade refrigeration system uses ammonia as the working substance. The evaporator…

A: A two-stage cascade refrigeration system Working substance= Ammonia (NH3) Temperature at evaporator…

Q: For the quick-return mechanism shown below, the rod DC rotates with a constant angular velocity of 1…

A: For the solution refer below images.

Q: Dimensions in mm Determine the magnitude of the force (in N) of the x-component of the internal pin…

A:

Q: Determine the magnitude of the force which member CD exerts on the pin at C. A 30% B 0.49 mi Answer:…

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: Determine the force in member EF of the loaded symmetrical truss. Assume no horizontal reactions at…

A: Solution: Given Data: Horizontal reaction forces at A and C are zero.   To Find: The force in the…

Q: Required information The cantilevered bar in the figure is made from a ductile material and is…

A: To Find : The magnitude for stress σx acting on the critical stress element. Given : The force are…

Q: For the mechanisms shown below determine the number of links, full joints, half joints and the…

A: The solution is provided below.

Q: C2(i)Assume that annual energy requirement of an industry is 20900 kWh ,we calculate that what will…

A: Given  Annual energy requirement= 20900kWh Coefficient of performance = 0.4 Loss factor value =…

Q: A strain gauges system mounted at a point on a structural member that is subjected to multiaxial…

A:

Q: 5. The semicircular gate is hinged at point A. What is the necessary force P needed to hold the gate…

A: The required force P. Given: The radius of the gate is R=15-8=7 ft. FBD: The free-body diagram of…

Q: PROBLEM 4: The basic barometer can be used to measure the height of a building. If the barometric…

A:

Q: E, +ɛ, ¸ E, - E, cos 20+ 2 - sin 20 2 From this expression prove mathematically by substituting…

A:

Q: 5. What is most nearly the lateral strain, en of the steel specimen shown if F,= 3000 kN, E=193 GPa,…

A: Given data : Load in X direction (FX)=3000 KNModulus of elasticity (E)=193 GPaPoissons ratio…

Q: Problem 1 True Stress-Strain A tensile test is performed on a specimen of a metal alloy. For this…

A: Write the given data. n=0.2εT1=0.10σT1=260 MPaσT2=260 MPa

Q: (a) The rotating elements in machine system often generate unbalance forces due to unbalance mass…

A:

Q: A factory produces product A.A consist of B(2 )and C(3), and each B is combined by D(2),E(2) and…

A: Given:The lead time of parts are given below;

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.