Etc +1 a-) What is the L value in mH? L= [Choose ] b-) How many ohms is the R value? R= [[Choose ] не c-) How many rad/s is the bandwidth (BG)? BG= с In the filter circuit given in the figure, C=10 µF, the center frequency of the filter is 7.5 kHz and the quality factor is 20. According to this; [Choose ] RE d-) How many rad/sec is the upper cutoff frequency? w2= [Choose ] + vo < < (Note: Perform your operations using at least 3 digits after the comma.)

Q: Briefly explain the operation of each block given in the table below. Block name Operation of each…

A: Digital compressor: A digital compressor is used for compressing air or refrigerant. The operation…

Q: In which method of fault diagnosis ,the input test signal is applied to each stages individually ? O…

A: The correct answer is dynamic testing.

Q: Q) The maximum error that is to be expected in any measure * quantities is known tolerance O…

A: The explanation is as follows.

Q: What is the advantage of using J-FET? a. Fail-safe O b. High predictability Oc. All of the above O…

A:

Q: For an op-amp integrator with R = 100KOhms, C = 10UF and a square wave input signal, the output…

A:

Q: What is the name of the signal which is indicated by the red line? 4- O A) Feedback B) Disturbance…

A: The given feedback system is non unity negative feedback system.   Here they have mentioned the…

Q: At what voltage will the upper comparator produce a low output of the 555 timer IC? Capacitor is…

A: When the capacitor is charging to a voltage lower slightly than 2/3Vcc, the output of the upper…

Q: I aksed for non inverting op amp configuration and the zero and poles value is also not same. Dont…

A:

Q: What are the typical parameters of Data Acquisition Boards?

A: From the given figure of data Acquisition Boards

Q: In measurement system, are needed where the output variable of a primary transducer is in an…

A: Energy from one form to another will be converted using a device called transducer. It is mainly…

Q: C/ Calculate load regulation of 7805 regulator has full load output voltage of 5.15 * V and no-load…

A:

Q: Define on-off ratio. Why series JFET has higher on-off ratio as compared to shunt JFET?

A: The series JFET is largely used as compared to the shunt JFET because of the high On-OFF ratio.

Q: Counter Output Question. input. 60 Hz rrr MOD-6 Counter Decade Counter Output (Hz)

A:

Q: G/ Desigh a square wave osillatr for Bequensy ZHZ and Sketch the Corresponding circait and the ut…

A:

Q: What is the cross over distortion in class B?

A: In the given questions we need to discuss about the cross over distortion in class B amplifier.

Q: How does R-2R DAC is better than Binary-weighted Resistor DAC?

A: Given that  How does R-2R DAC is better than Binary-weighted Resistor DAC?

Q: Design a 3-input priority encoder such that D₂: The highest priority •D₁: Middle priority • Do: The…

A:

Q: 33. Forward voltage drop of LED is of the order of i) 2 to () 2 to lov 4 v ii -2 to -4v (り+2 o -4v.…

A: In this question,  Choose the correct option What is forward bias voltage drop. Of the LED.    as…

Q: How many states will there be in a 4-bit ripple counter?

A: In an n-bit counter, the total number of states = 2n.

Q: What is soft switching designed to avoid? A. Rising edge resonance B. Switching losses C. Zero…

A:

Q: Controller Load

A: Given Data:A step up chopper with,Output voltage Input voltage To Find:The duty cycle .

Q: The inherent problem with Master-Slave flipflops are its unreliable operation caused by

A: Master-slave flipflop: It consists of two sections master and slave. These are triggered from the…

Q: In a 555 timer IC with Vcc 9V, the voltage across the series resistive network holds the negative…

A: The working rule of the 555 timers is by considering the square graph of the 555 clock IC. The first…

Q: Briefly explain the operation of each block given in the table below. Block name…

A: (1) Digital compressor - It is used in transmitter side. It transmit low bandwidth signal. It…

Q: (B) R, - 10 ka Si Si Vo

A:

Q: Q5/B- What the difference between encoder and priority encoder

A:

Q: Q4) Design an arithmetic logic unit (ALU) that can do the following operations (A AND B, A-B. B-A, A…

A:

Q: In CRO, the volts/cm knob indicates scale on vertical axis. Select one: O True O False

A: In CRO there are two axis Horizontal axis Or x-axis  And vertical axis Or y-axis

Q: Kindly assist to check if the new design I made with the insertion of this multiplexer works.

A: According to the question, we need to check the design shown below

Q: Design a negative edge triggered asynchronous counter that counts by repeating the sequence of…

A: we need to design negative edge triggered asynchronous counter that counts by repeating the sequence…

Q: Vertical Amplifier is used in CRO to Select one: a. Amplify signal from input b. Delay the input…

A: Input signal is given to vertical amplifier

Q: The hardware sytem operate under a static dicipline with the following thresholds VIL=1.3V…

A:

Q: The contents of the designated register pair are decremented by 1 and the result is stored in the…

A:

Q: For 4-bit DAC Binary Weighted Resistor Method, if the Vref = 20 what is the output current for the…

A:

Filter

A filter is a device or process which removes some of the unwanted features or components like frequencies from a signal in signal processing. The feature of filters is the complete or partial suppression of some part of the signal, and filtering is a class of signal processing. This most often means removing some frequency bands or some frequencies. In the frequency domain, the filters do not exclusively act, especially in the image processing field many other targets for filtering exist. Without having to act in the frequency domain, the correlations can be removed for certain frequency components and not for others. The filters are widely used in electronics and telecommunication, in television, radio, radar, audio recording, music synthesis, control systems, computer graphics, and image processing.