Estimate the matrix of the structure to solve with the method of knots. Determine the stresses in each bar and the link reactions.

Q: Situation 1: A flexible cable and rigid boom system is used to lift a load of 65kN at the end of…

A:

Q: The bar AB is supported by a frictionless inclined surface at A and a % in diameter pin at B that is…

A:

Q: Task #1 Develope a MATLAB code that calculates the following using the Finite Element Method. Refer…

A:

Q: The structure shown below supports a vertical load P = 100 N. The sloped wall at A is frictionless…

A: The angle θ=54°. The angle β=55.3°. The force P is 100 N

Q: Need a detailed solution in Handwritten format. (FBD required)

A: Step 1: Step 2: Step 3: Step 4:

Q: Solve the reinforcement using the method of nodes. Calculate the reactions and forces in the bars…

A: Consider the following FBD Reactions can be calculated by equilibrium equations Taking sum of…

Q: A rod has a solid circular cross section with a diameter of 40 mm is subjected to the shown loads.…

A: To find: The state of stress at point A. Given: The area moment of inertia of solid circular cross…

Q: Determine the support reactions on the member in 900 N figure. The collar at A is fixed to the…

A: For the given member  To determine support reactions on the member

Q: The assembly consists of two rods AC and BD attached to the 100-lb uniform rigid beam AB. There is a…

A:

Q: calculate the force in Member BE if F=172, A=373, and B=280. On your scanned work, also solve for…

A: FREE BODY DIAGRAM is a diagram of the system which represents all the forces acting on the system.…

Q: Situation 5. Determine the member forces CD and GF using any method. Indicate if (T) or (C). 2 kN…

A: Given: P1 = 2 KN P2 = 1.5 KN To find: FCD and FGF

Q: Compute the design factor in the middle portion only of the rod AC if the steady vertical force on…

A:

Q: 9. The rigid bars ABC and CD are supported by pins at A and D and by a steel rod at B. There is a…

A: First we need to calculate load on the string.

Q: 4. Compute all of the support and internal hinge reaction components for the structure and loading…

A:

Q: is it okay to solve this even if it is not in equilibrium? Why?

A: Solution:

Q: 2. Compute for the force in members FH, GH, and GI (USE METHOD OF SECTIONS) *For load P, take the…

A:

Q: Problem 8-21: If the load has a weight of 600 lb, determine the maximum normal stress on the cross…

A:

Q: Problem #1 (Sections) cos 08 10 kips 30 kips 3. sin 06 3. Calculate the forces in Members 'CD',GD',…

A:

Q: Compute the outer and inner diameter of the hollow circular rod when it is subjected to an axial…

A: Given data as per question Axial pull = 350 KN Allowable stress = 125 N/mm2 Thickness of rod = 10 mm…

Q: Solve for the internal force in member EF for the truss below. Provide answer in kips to one decimal…

A: Solve for the internal force in member EF for the truss below. Provide answer in kips to one decimal…

Q: For the figure shown, show a free body diagram with section cut that could be used to determine the…

A:

Q: The "C" clamp shown in the following figure has a rectangular cross section at location "a-a" with a…

A:

Q: The 7/8-in.-diameter pins at A and C that support the structure are in single shear. Find the…

A:

Q: The steel framework is used to support the reinforced stone concrete slab that is used for an…

A: To Find : The load that act along members BE and FED. Given : The thickness of slab is t=200mm. The…

Q: Compute the maximum tensile and compression Stresser developed in the beam that is loaded and has…

A:

Q: Abraced cantilever is loaded as shown in figure. All the members have the same cross sectional area.…

A:

Q: A frame is given above and an external load R is applied at point C. Pin connection at D is in…

A: Given data: External load R=45 kN applied at 'C'. Diameter of pins 'B' and 'D': dB=13 mm ; dD=8 mm.…

Q: For the symmetric queen truss shown here, determine the length of member DC. Round your answer to…

A: For the solution refer below images.

Q: 5. An angle bracket ABC is restrained by a high- strength steel wire CD, and it supports a load P at…

A:

Q: The homogeneous bar AB weighing 2000 lb. is supported at either end by a steel cable. Calculate the…

A:

Q: 3. Determine the normal force, shear force, and moment at a section thre ugh point C.Take B 0.1' m…

A:

Q: Write the solution for the following: Member BC = -447.21 Member DF = -800 Member CE = 100

A:

Q: For the cantilevered handle shown, the force Fy applied at D is 1000 lbs in the y-direction. Please…

A: Since the handle is cantilevered, the loads at point C will be equal to the applied force and…

Q: 311(MECHANICS OD DEFORMABLE BODIES): PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL…

A:

Q: The composite bar is firmly attached to unyielding supports. Compute the stress in each material…

A: Given P = 320 kN = 320 X 103 N To find Stress of each materials

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter of this chip…

A: Draw the free-body diagram of the system as shown below, Taking moment about C,…

Q: The figure shows a setup where when the member AB is horizontal and the unstretched aluminum bar…

A:

Q: The internal drag truss for the wing of a light airplane is subjected to the forces shown. Determine…

A:

Q: B D F 3. A Howe truss is loaded as shown below, P = 32 kN. a) Find the support reactions at A and Н.…

A:

Q: The lap joint is fastened with four 4/5 in-diameter rivets. The working normal stress for the plates…

A:

Q: 5-4. Determine the load in member CH of the truss shown in Figure P5-4. 6 kips 15 kips CY BY D X 20'…

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.