Estimate the frontal area of the car shown in the accompanying figure 7.50. 68.5 in 50.9 in

Q: Large vehicle will impose more pressure and damage to the pavement surface than the small vehicle.…

A: This question is related to the Highway and Traffic Engineering.

Q: * Which of the following statement is not true about site clearing? Site clearing in rural area is…

A: To find out the false statement about the site clearing for highway.

Q: a) Find the equivalent resultant force-couple system acting at point A. b) If the force system is to…

A:

Q: Question number (14) Highway Engineering civil engineering

A: Answer - True Full depth asphalt is a type of flexible pavement. With these types of covers, the…

Q: * Excavation can be conducted uphill and downhill. O True O False

A: This question is related to the Highway Engineering and Traffic Engineering. There is question…

Q: Solve all parts of  (A)   Hand written and clean writing please

A: Given:Required:Support reactionFBD of each sectionV and M equation for each sectionShear force and…

Q: Assume cc=0.62 and cy-0.98, calculate the discharge through a 120-mm diameter orifice under a head…

A: D=120mm h=6.5m Cc=0.62 Cv=0.98

Q: * What is the definition of grubbing in site clearance and preparation? Removal and disposal of…

A: This question is related to the Traffic and Highway Engineering. In this question, Ask question…

Q: An engineer bought an equipment for P500, 000. Other expenses including installation amounted to…

A:

Q: hway Engineering civil engineering

A: We know Degree of compaction is given by R=Compacted SGExperimented SG

Q: Identify two type of strains that have been used in order to assess pavement performance. O Linear…

A:

Q: A rectangular gate 1.5m wide and 3m high is vertically submerged in water with its top edge…

A:

Q: A rectangular scow has a draft of 1.8 m in fresh water when erect. The scow is 6m wide and 12m long…

A:

Q: discuss the Applications of Computational fluid dyanamics in the field of civil engineering

A: Fluid dynamics In physics and engineering, fluid dynamics is a subdiscipline of fluid mechanics that…

Q: An asset is purchased for P500, 000.00. The salvage value in 25 years is P100, 000.00. What is the…

A: Depreciation can be calculated by  Straight line method Decline balance method Sum of years digit…

Q: Question number (19) Highway Engineering civil engineering

A:

Q: The discharge through a Venturi meter is 58 li/sec. The diameter of the pipe is 750 mm and the area…

A: Calculate the diameter of the throat, Area ratio = dpipedthroat                41=750dthroat…

Q: Engineering Fundamentals – An Introduction to Engineering 6th Edition – Saeed Moaveni Chapter 6…

A: a)Provide the dimensions in the equation F=ma as shown below.

Q: * Consolidation is a process to reduce the moisture content within soil structure. True A O False…

A: Consolidation is a process in which soil reduces it's mositure content under the action of applied…

Q: Q.2 An open, clean glass tube (0 = 0) is inserted vertically into a pan of water. The surface…

A: Given data- An open clean glass tube θ=0, Surface tension- σ=7.34×10-2 N/m, The water level in the…

Q: Subject: Fluid mechanics

A: Given data Discharge at A,  QA= 10 ft3/sec QA+QB= 10 ft3/sec           …(1) Hence head loss in B and…

Q: Each standard axle consists of 2 tyres. O True O False

A: To Determine Whether the given statement is true or false.

Q: * Which of the following statement is not true about compaction for asphaltic concrete? The…

A:

Q: Chemical oxygen demand (COD) is measured through the reaction of organic compounds with potassium…

A: Given data: Normality of titrant = 0.545 Amount of titrant added to blank (a)= 37.8 mL Amount of…

Q: 3.49 Determine the minimum volume of concrete (y = 23.6 kN/m²) needed to keep the gate (1 m wide) in…

A:

Q: Breakdown rolling shall be carried out using steel wheeled roller. * True False

A: Breakdown rolling may be accomplished with static or vibratory steel-wheel rollers.

Q: A flow field has x and y components of velocity (w = 0) defined as follows: u = 2x v = x + 2y (u and…

A: The correct option is ax=4x and ay=4x + 4y

Q: Mastering Engineering with Pearson eText -- Access Card Package (14th Edition) Chapter 3.4, Problem…

A:

Q: An asset is purchased for P9, 000.00. Its estimated economic life is 10 years, after which it will…

A: We have to asked book value during the third year if the sum of the year digit depreciation is used…

Q: * Thickness and CBR value for 1 meter of subgrade soil are as follows:

A:

Q: Activity 1. A 0.60N bullet with a velocity of 360 m/s strikes a 90N block of wood moving a velocity…

A: Given data- To find- Resultant velocity.

Q: 1Q. A certain gas weighs 16.0 N/m³ at a certain temperature and pressure. What are the values of its…

A:

Q: The following are the soil strength tests conducted prior to the pavement thickness design except?

A: Soil testing is done prior to the construction of highway pavement in order to evaluate its strength…

Q: 2Q. Calculate the density, specific weight, and specific volume of air at 120°F and 50 psia.

A:

Q: * The compaction of granular materials should : be conducted using the pneumatic roller consider the…

A: Granular material is generally considered to be mixtures of clay, sand, and gravel.

Q: A vertical rectangular gate 1.8m wide and 4.2m high is submerged in oil (SG-0.88) with its bottom…

A:

Q: Calculate the equivalent standard axle for each truck based on ATJ 5/85 (2013). Arrange the truck…

A:

Introduction to Engineering Design

Students are often confused with engineering and design. The term engineering design has two words with different meanings, engineering, and design. The term engineering implies applications of laws and principles of science to design and analyze physical structures and components. In civil engineering, students apply the concept of physics and chemistry to design and build structures and buildings. In engineering disciplines, the term design means determining the dimensions, loads, and associated influences on the component due to the applied loads such as stresses and deformations. The estimation of such parameters is crucial to make the component or structure foolproof.