(ESA-3.01) The best selection to meet a requirement for an amplifier with a very high voltage gain is O 1. a common-collector. O 2. a common-base. O 3. a common-emitter. 4. an emitter-follower.

Q: Thevenin and Norton Equivalent: 15). For the circuit in Fig. 4.109, find Thevenin equivalent between…

A: We need to find out thevenin equivalent circuit and norton equivalent circuit

Q: Generation engineers are more inclined to an operation in a closed system as compared to an open…

A: Nowadays Electricity is a major part of any country's growth. The demand for power supply is…

Q: Why is Preventive Maintenance (PM) important?

A:

Q: With neat diagram explain the parts of galvanometer

A: The galvanometer is the device used for detecting the presence of small current and voltage or for…

Q: Discuss the role of power system stability analysis in ensuring the secure and reliable operation of…

A: Power system stability analysis plays a crucial role in ensuring the secure and reliable operation…

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: Briefly explain the working of following power plants a) Thermal Power plant b) Hydel power plant

A: thermal power Plant coverts heat energy to electric power / Energy. The basic principle of these…

Q: What is the Possibility of Incorrect Decisions?

A: Probabilities of correct and incorrect decisions can be seen in given graph. Here we can see that it…

Q: 9.a. What should be done with the connector ferrule once a connector is attached to a fiber optic…

A:

Q: What are the key challenges in power transmission within a power grid?

A: Key challenges in power transmission within a power grid?

Q: A1. Voltage sag is common power frequency disturbance that can last half of a cycle to several…

A: Voltage sag is an important consideration while analyzing the power quality. It is always…

Q: Discuss any two types of signalling mode with a neat diagram.

A: two types of signaling mode with a neat diagram

Q: How does power system stability analysis help in ensuring the reliable operation of the electrical…

A: Here we need to explain how power system stability analysis helps in ensuring the reliable operation…

Q: Carbon resistance Q 1) The potential difference across the two ends of a 1.5m tungsten wire is 907…

A: The solution can be achieved as follows.

Q: Explain the concept of electrical grid reliability and its importance.

A: To explain:the concept of electrical grid reliability and its importance.

Q: Define the terms "load shedding" and "voltage regulation" in the context of power systems. How do…

A: Load SheddingLoad shedding is a controlled and intentional reduction or shedding of electrical load…

Q: I dont get it. howcan I make sure its in low condition?

A: You have asked that how to make sure it is in low condition.

Q: What is the acceptable minimum value of leakage current of HI-POT Test of electrical cables. Can you…

A: According to the question,what is the acceptable minimum value of leakage current of HI-POT Test of…

Q: Choose the correct answer 5-  ________ related ranging errors to the dispersion in measured…

A:

Q: Please answer in typing format

A: The Peltier effect is the result when electric current is passed between two materials,such that it…

Q: Refer to the National Electrical Code or the working drawings when necessary. Where applicable,…

A: We are authorized to answer one question at a time, since you have not mentioned question you are…

Q: a Explain the procedure for preventing an overload or a short circuit in a domestic wiring b. What…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: What Is Tripping My Circuit Breaker?

A: Circuit breaker: It is an electric safety device, which can interrupt the electric current flow when…

Q: Electric Powers System for Nonelectrical Professional can you describe effective preventive…

A: Electrical Preventive Maintenance (EPM) is the act of leading routine assessments, tests, and the…

Q: The balanced system below has a phase voltage of 120 V. It supplies a balanced load coil that is…

A:

Q: Compare the nested and the NPC topologies in terms of the blocking voltage for the switches employed…

A: We need to compare NPC and Nested topology.

Q: Compare the nested and the NPC topologies in terms of the blocking voltage for the switches employed…

A: Concept- The nested and the NPC topologies in terms of the blocking voltage for the switches…

Q: Discuss the concept of an Electrical fault. How can we prevent such catastrophic incident for such…

A: Electrical Fault in an electrical equipment or apparatus  is a kind of imperfection in electrical…

Q: 5 - What should be done first when a person being electric shocked seen? A) Cut off the electricity…

A: If we seen person being electric shocked then we need to do take some necessary action

Q: How can your criteria for selecting solar PV panel with maximum power point system (MPP).

A: Selection criteria for solar PV panel PV module is an assembly of photovoltaic cells that are…

Q: 3 ● Row 1 2 4 5 6 7 8 9 10 11 12 13 14 15 Refer to the National Electrical Code® or the working…

A: Here it is asked to solve question (2), so we are solving that question only. “Since you have posted…

Q: 13-Find the Thevenin and Norton equivalent circuits between ab. 2 A a 6 0 18 V 3 A 10 V

A: Given:

Q: What is meant by Electric Bid Package?

A: Bid package means the collection of the pertinent portion of the construction documents into a…

Q: The primary and secondary voltage drops respectively are: 96.2 volts and 9.62 volts O 0.962 volt and…

A: In this question we need to find a   primary and secondary voltage drop of the given signal phase…

Q: How Rth connected with the load resistance, explain

A: RL will be  connected in series with  RTH  as shown in the example.

Q: Fill the following blanks in the sub-program with suitable numbers to generate 7 sec delay.

A: Explanation:The outer loop (D2) is initialized with a count of 7 to achieve a 7-second delay.The…

Q: Explain the concept of load balancing in electrical power systems

A: Concept of load balancing in electrical power systems.

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.