ERROR or MISTAKE 1. RECORDING NUMBERS INCORRECTLY (EXAMPLE 78 IS READ AS 87) 2.TAPE NOT STRETCH STRAIGHT 3.TAPE NOT STANDARD LENGTH 4.VARIATIONS IN TENSION 5.ADDING OR DROPPING A FULL TAPE LENGTH 6.IMPERFECT ALIGNMENT OF TAPE 7.ADDING A CM., USUALLY IN MEASURING THE FRACTIONAL PART OF TAPE AT THE END OF THE LINE 8.TAPE NOT HORIZONTAL

ERROR or MISTAKE 1. RECORDING NUMBERS INCORRECTLY (EXAMPLE 78 IS READ AS 87) 2.TAPE NOT STRETCH STRAIGHT 3.TAPE NOT STANDARD LENGTH 4.VARIATIONS IN TENSION 5.ADDING OR DROPPING A FULL TAPE LENGTH 6.IMPERFECT ALIGNMENT OF TAPE 7.ADDING A CM., USUALLY IN MEASURING THE FRACTIONAL PART OF TAPE AT THE END OF THE LINE 8.TAPE NOT HORIZONTAL

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A machine component is subjected to the forces and couples shown. The component is to be held in place by a single bolt that can resist a force but not a couple. Determine the distance of the bolt hole from point G if it is to be located on line FG. 125 N 15° 200 N E 50 mm 42 N-m 520 mm 240 mm 50 mm D 70° 40 N-m 640 mm H C 80 N 20 N 180 mm B 50 mm
Problem Solving : Round off your final answer to 2 decimal places. 20KN DI L4 H ! T 3m SKN ↑ 3m ↓ 4m ·0 13 G By L2 F A Barn E J * 3m 311) 3m For the frame provided below, consider the following properties: * Members along Level a Regular Hexagon with side = 300mm * Membens along Level 3 Regular Trapezoid with longer side = 500mm, shorter side = 400mm, Height = Soomm * Members along Level 4 Regular Trapezoid with longer side = 300mm, shorter side = 200mm, Height = 400mm * Members along Line 1 Hollow circular Tube, Outer Diameter = 550mm, Inner diameter = 350mm * Members along Line 2 Hollow Square Tube, Outer Breadth & Height = Soomm, Inner Breadth & Height = 300mm + Members along Line 3. Equilateral Triangle with side = 650mm + Members along Line 4 Hollow circular Tube, Outer Diameter = 400 mm, Inner Diameter = 300mm Solve the following for ALL members: 1. Axial Forces 2. Shear Forces 3. Moments
9:56 Edit Done A 33-kilogram concrete block A is kept from moving down the plane inclined at an angle 0 from the horizontal by a 10-kilogram metal ball B attached to the block by a cable wire through a pulley as shown below Find e A В More
Given: Std. Temp. = 68°F, Std. Length = 100.00’ Std. pull (supported) = 12 lbs. E=29,000,000 lbs./in.Std. pull (unsupported) = 20 lbs. A (cross sectional area of tape) = 0.005 in.².A line was measured and recorded as 275.50’ on a day when the temperature was 28 F. The tape used to measure theline was found to be 99.975 feet long when compared to a standardized tape of 100 feet. Tape is unsupported. What isthe actual measurement of the line? All other conditions are standard
METERS | FEET MODEL: IA6BJM SIZE: 8" x 6" x 13" RPM: 1750 PRESSURE MAX: 120 PSI 76+250 GRAPHIC 61+200 Ø13," (75 HP) SCALE. 70% 75% 80% 82% 83% 60 GPM Ø12%" (60 HP) 84% 83% 82% 80% 46+150 Ø12%" (50 HP) 75% 70% 65% A 100 BHP Ø11%" (40 HP) 31+100 010%" (30 HP) NPSHr ft m 75 BHP 60 BHP 30+9 15+50 50 BHP 3О ВНР 40 BHP 20+6 NPSHR 10+3 GALLONS PER MINUTE LITERS PER MINUTE Refer to the system curve drawn on this pump curve. If the pump is to move 1200 gpm, what is the estimated NPSH Required by the pump (ft)? 1136+300 2271+600 006+2ODE 4543+1200- 5678+1500- 6414+1800아 7949+2100- 9085+2400- 11356+3000야 10 FEET
Help me in this.
Determine the coordinates of the centroid of the shaded area. (X,Y) Blank 1 = (Blank 1, Blank 2) mm Blank 2 Add your answer Add your answer 10 30 y 1 15 10 55 15 25 15 Dimensions in millimeters ...
ASAP
Please Fill in the gaps below
A steel bar shown is made up of two segments. Determine the displacement of A relative to fixed support D.
Use the given in set b
Please provide the whole (not shortcut) and correct solution with figures. thank you Given: x =175mm Rivet Dia.=20mm y=200mm Fy=248Mpa Fu=400 Mpa Bolt Dia.=22mm