electrical motor is used to drive a conveyor belt, which carries 10,000 products per hour for a distance of 200 m up and an incline of 1 in 13 ( sine). Each package weighs 50 N. The total power due to friction during the drive is 20 kW. Calculate the total power needed from the motor to drive the conveyor belt to complete the task described above

Q: 11. The direction of the magnetically induced current will be (parallel, perpendicular, opposite) to…

A: 11. The concept is based on Lenz's law.12. The concept used here is production of A.C current under…

Q: Sölve the given problem: The figure below shows a top view of two conducting rails on which a c…

A: If a conductor is forcefully brought under a magnetic field, there should be an induced current in…

Q: (a) Calculate: (1) The slip and line current. (ii) The torque and mechanical power. (iii) The…

A:

Q: What part does the frequency of alternating current play in the operation of an electric motor?

A:

Q: A 3,700-turn solenoid produces 677,000 Maxwell when excited by a current of 3.5 amps. Calculate (a)…

A:

Q: Give reason(s) for any difference between measured and nameplate values. Discuss the values obtained…

A: It is asked to tell the reasons for the difference in speed between measured and nameplate values.…

Q: Explain different the neat sketch of speed torque profiles. a. 0< Slip1

A: Need to draw speed vs torque curve of induction motor

Q: Activity 2: Consider the sketch of an AC machine shown in Figure 1. Draw the position of a magnet…

A: Given Data:The sketch of the stator windings of a three-phase AC machine as,To Find:The position of…

Q: 5. A dynamo has a iron loss of 1100 W of which 65% is the hysteresis loss when operated at a speed…

A: An alternator/Synchronous generator is a type of electrical machine that converts mechanical energy…

Q: Coleman started running at a speed of 10 kph. Five minutes later, Bolt started running in the same…

A:

Q: 6. A loop measuring 15 cm on a side has 50 square turns. When placed in a 0.75-T

A:

Q: A DC generator feeds a load consisting of 22 lamps, each lamp capacity 100 W,220 V, calculate the…

A: We need to find out induced voltage for given generator for given load .

Q: What is the minimum diameter of a steel shaft which will be used to operate a 14 Kn-m torque and…

A: What is the minimum diameter of a steel shaft which will be used to operate a 14 Kn-m torque and…

Q: to magnetic flux density of 1.0 T at the airgap. The details are provided as follows: Number of turn…

A: Given,Magnetic flux density of air gap(B)=1.0TNumber of turn of field winding in each pole(N)= 200…

Q: A mechanical load of 0.5n moved by a 12 v linear motor with movable member of 0.2 meter long moving…

A: i) For the steady-state condition, the force on the mechanical load should be balanced. The force…

Q: Choose correct answer : If the speed of the DC motor is increases then the A) Supply voltgae…

A: E = p q Z N / 60 * A p - no of poles q - flux per pole Z - no of conductors N - speed A - no of…

Q: Answe the ff . 1.)____ It is a rotating machine which functions by producing a relative motion…

A: An electrical generator is a rotating machine which functions by producing a relative motion between…

Q: D. Scientists plan to do a third experiment in order to find a generator with the greatest useful…

A: Current through a conductor generates a magnetic field which is circular in nature around a…

Q: If the area of hysteresis loop of a material is large, the hysteresis loss in this material will be…

A: In this question , we will write hysteresis loss..

Q: The following questions refer to to a 6-pole DC generator has a simplex lap-wound armature…

A: It is given that: Number of poles=P=6288 coils of 1 turns eachResistance of each turn=0.01 ΩFlux per…

Q: Draw the following: a. Magnetic poles b. The direction of current, assuming conventional

A: We need to draw magnetic poles and the direction of current in the given diagram.

Q: A dc machine has a constant of k=10, þ=0.3web, V3=200V, and full load speed of w=20rad/s rotates…

A: a dc machine has a constant of k=10, Φ=0.3 Web, VB = 200V and full load speed of ω=20 rad/sec…

Q: How much work could be performed by a 5968 W (8 hp) motor in 6 hours?

A:

Q: Calculate the flux in a magnetic circuit that has a reluctance of 0.06, if the 2,500 turn exciting…

A: Given units are in CGS system Relunctance S = 0.06 N = turns = 2500 current I = 2.5 A

Q: A 4-pole shunt generated has a lap connected armature with 728 conductors. The flux per pole is 25…

A:

Q: For any feasible combination of generators, the load will be dispatched based on a. Heat rate b.…

A: For a power system that contains number of generator , ' Equal incremental cost rule ' determines…

Q: A three phase transmission line to line capacitive reactance value is 12 ohms. If the charging…

A:

Q: A lift motor has to move a fully loaded lift 6m between floors in 8.5s. The lift has a mass of…

A:

Q: Q6: Two loads of rating (2200VA, 10A, 220V, 50HZ) for each. One of them is 100m far away from the…

A:

Q: Question 48 Another name for a hysteresis loop is: A) B) C) D) field intensity flux density the B-H…

A: Hysteresis loop: It is a four quadrant graph. It is drawn between magnetizing force H and , magnetic…

Q: Question 7 Using the magnetorheological properties of the materials, how could we design a product…

A: Properties of the materials:

Q: A 45 kW, 131 V DC shunt generator has an armature and field resistance of 0.04 ohms and 65 ohms…

A: Load current = power delivered to load / load voltage                         = 45000/131…

Q: Q4-A 4-pole,35KW,250V d.c. generator has a wave-wound armature with 240 turns. If the brush lead is…

A: First calculate total armature current and using formulas of demagnetizing and cross magnetizing…

Q: A linear machine has the following parameters: The battery voltage, V = 120 V, The internal…

A:

Q: 5. A square loop of wire carrying a current of 15 A is in a magnetic field of strength 2.20 T. If…

A: In this question We need to determine the maximum torque of the square loop.  We know Torque = NIBA…