1. In an automatic mixing operation the sequence of operation is as follows: When the start button is pressed fill the tank with Liquid B till it reaches X1 and then fill the tank with Liquid A till it reaches X2. Once the level of Liquid reaches X2, turn on the motor for another 20 seconds for mixing process. After the timer stops timing, empty the tank by opening the mixture outlet. X1 and X2 are capacitive proximity sensors and there are start, stop and emergency stop push buttons. XO START X1 STOP YO (Liquid A Inlet ) EMERGENCY STOP YI(Liquid B Inlet) Y2(Mixture Outlet) For the system explained above answer the following: a) Provide the Allocation List b) Draw the Grace and extract the grafcet equation c) Draw the Ladder Diagram

1. In an automatic mixing operation the sequence of operation is as follows: When the start button is pressed fill the tank with Liquid B till it reaches X1 and then fill the tank with Liquid A till it reaches X2. Once the level of Liquid reaches X2, turn on the motor for another 20 seconds for mixing process. After the timer stops timing, empty the tank by opening the mixture outlet. X1 and X2 are capacitive proximity sensors and there are start, stop and emergency stop push buttons. XO START X1 STOP YO (Liquid A Inlet ) EMERGENCY STOP YI(Liquid B Inlet) Y2(Mixture Outlet) For the system explained above answer the following: a) Provide the Allocation List b) Draw the Grace and extract the grafcet equation c) Draw the Ladder Diagram

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

i need the answer quickly
There are 2 1000Watt 3-phase asynchronous motors in a Walnut Cracking machine (it is desirable to operate the motors in a way that they remain in star connection). When the "Start" button is pressed, the 1st engine will start immediately, 3 seconds after the 1st engine starts, the 2nd engine will also start. After the two engines work together for 4 seconds, the 1st engine will stop, the 2nd engine will start and stop for another 10 seconds. If the "Stop" button is pressed at any stage of the operations, the motors will stop. The rotation directions of the motors are required to be opposite to each other. Draw the necessary power and control circuit.
220v AC motor can be installed to PLC output pin..... O Directly O Via relay O Via contactor O Via push button O Other:
Please solve this question in control system quickly
7. The output terminals of most servo motor systems are marked with the lettersA. X, Y, and Z.B. U, V, and W.C. T, Q, and R.D. C, D, and E.
4. A stepper motor has a step angle of 1.8° and it is driven at 6500 pps. i) Calculate the shaft speed. a) Calculate the resolution. ii) iii) Calculate the motor speed in rpm. iv) Calculate the pulse required for 5.5 revolution. Calculate the rotor teeth given the stator teeth is 50. v)
Please provide Handwritten answer
write true or false in the following sentences: 1. Load torques which always oppose the motion and change their sign on the reversal of motion are called passive load torques. 2. The control rectifier drive has low atmature current ripple compare to de to de chopper drives. 3. The main difference between dynamic breaking and regenerative braking of de motor is the disconnection the source from de motor in dynamic braking. 4. Two quadrant operation of de motor can be obtained from thee phase semiconverter. 5. de-de four-quadrant drives can be supply high power than ac-de four-quadrant drives.
please sovle part (iv)
A 51S2 relay has the following settings: Pickup 2 Amps Curve U1 TD 5 If 8 Amps enters the relay, what is the pickup time in seconds to 2 decimals? Enter the number only, no units. Answer is +/- 0.01
You’re powering up a new motor in a brushless motor control system. After moving the shaft of the motor lightly left to right, the motor reverses direction and runs away. What’s the problem? A. Power transistor failureB. Wrong motor typeC. Reversed tachometerD. Reversed hall-effect sensor
7