QUESTION 4 When no key is pressed the input port (Port B) will read Port A (output) DO 4 D1 8. D2 A B. E E. D3 Vc D3 D2 D1 DO Port B (input) 0000 B 4567 1111 B Cannot tell.

Q: R1 Write Datap00O 1001 Read Data 1 DMX MUX R2 Write Register Read register number 1 R3 R4 Read Data…

A: The input of combinational circuit only depends on present input. Initially the values are 0 0 0 0.…

Q: The OR gate always has 2 inputs and one output can have more than two inputs and more than one…

A: Choose the correct option How many input and output of OR gate?

Q: What is the difference between the pins under number 1 and the pins under number 4, and mention when…

A: Given,

Q: . register or registers can be used for input and output purpose O DX O BX O cx O no one AX

A: AX comes under the category of the primary accumulator. It is used as the Input/output register it…

Q: Write a program in 8051 to copy the contents of code ROM addresses 0100H-0102H to internal RAM…

A: In the program microcontroller require to copy the contents from ROM address 0100H-0102H and store…

Q: When the MPU takes an interrupt it runs a program called an INT INTR ISR IRQ SUV

A: When the microprocessor takes an interrupt, it halts the programs run for the various peripheral…

Q: If the four output lines of a demultiplexer are YO, Y1, Y2 and Y3, and the two select lines are…

A: In this question , we will write output selected  for select lines 1 1...

Q: Choose the correct instruction that will read data in from an I/0 device. IN AL, 60 IN 60, AL OUT…

A: In an I/O device the command "IN" represents the input command Here IN AL,60 means that move a…

Q: If output port A = 1101 B and the "9" key is pressed, port B will read, - [Be careful to check the…

A: PORT A (OUTPUT) = 1101 B Note that D3 is the MSB. Redraw the table as per circuit diagram.

Q: 1- Find is the written formula correct? If it's wrong,write the correct formula. MOV BL,DX MOV AX,BX…

A: As per bartleby guidelines I could solve only one question at a time for remaining questions you…

Q: Q3/TO design Carry Look ahead adder that add two (9-bit) numbersmust using * O 9 X-OR O 12 X-OR О 15…

A:

Q: When no key is pressed the input port (Port B) will read

A: in the given circuit the matrix connected two ports are given in which port A output is applied to…

Q: Design an adder ccb that adds three 8 bib numbers using 8 bib fA blocke=-

A: Circuit which adds three 8-bits number is designed as shown below

Q: Problem #3: board has three clocks that can be seen in the table below: Table 3-2 Pin Assignment of…

A: Let the input clock signal is 10MHz, ADC_CLK_10 clock signal. Which is provided to the LPM counter.…

Q: *13. Compute the missing values to complete the following table relating to analog to digital…

A: We know relationship between analog input and digital output .

Q: The main difference between a register and a counter is a register has no specific sequence of…

A: In this questions we need to tell about the main difference between register and counter.

Q: If the four output lines of a demultiplexer ar YO, Y1, Y2 and Y3, and the two select lines a given…

A:

Q: If the voltage on pin A2 is 4.405V, what value will analogRead(A2) return from the ADC

A: While converting analog values to digital input analog signal is first sampled and at different…

Q: If output port A = 1011 B and the "6" key is pressed, port B will read Port A (output) 0. 21 31 DO 4…

A: If input port A=1011 B  , and the "6" key is pressed then port B will read : options are: 1111 B…

Q: Enter the correct value (either 1 or 0) in each box; consider each row carefully before deciding on…

A:

Q: Which is correct in case of Computer controlled system?

A: Given Data:There are 4 statements regarding computer-controlled systems.Required Data:Here, we need…

Q: multiplexer contains. multiplexer contains.... select lines 4-1 4 O 20 8 O select lines 16-1 4 O 8 5…

A: In this question we need to choose a correct option

Q: BCD to decimal decoder D1=? 4X10 A 1. 0001 Decod B 2. 1000 3. 1111 8 8 3 8 8 8 8 8 AAAAAAA

A: In the given decoder we have 4 inputs A,B,C,D and 10 outputs D0,D1,D2 ,D3 ,D4,D5 ,D6,D7,D8,  D9…

Q: b/ We obtained the following values from alternating voltage measurements by means of a d-organza…

A:

Q: 4 to 1 What is the value of J in SoP format? MUX C' 1 Flip-Flop А В Q 2 to 4 Dec AH O A'BC + AB +…

A:

Q: * bit current ADC. 0000 represents 4 4mA and 0001 represents 5mA (the resolution is 1mA). To get…

A: This question is related to Analog to digital converters

Q: QUESTION 10 Which ones using to make "set" pin 2 and pin 6 in Port A register for TM4C? wwwm www A-…

A: From the given options: The binary format of the given numbers are: 0xc2:1100 0010 0x44:0010 0010…

Q: Identify which one of the three IC ?chips is XOR gate 74LS 136 5.21 14 A B C A B c O HD74L SOOP 2426…

A: The given IC A (74LS00P) is a two-input NAND gate.

Q: Configure the following counter such that it counts according to the following sequence:…

A:

Q: R X2 X3 1 -1 O 0.4 O 0.6 O 0.2 0.1

A: Fig: Given signal flow diagram In the above SFD  No. of the forward path  i x1x2 =1×1=1ii…

Q: the first state is 00 00 as indicated below, What will the last stated be after the last clock and…

A:

Q: The voltage gain for each stages are and respectively. (two decimal places). Rs-62002 Z=15KQ Zo=22k0…

A: We need to calculate Gain for individual stage

Q: Consider the transistor inverter on the right driving a dc motor modeled as a 1.2mH inductor. The…

A: According to the question, for the circuit shown below, We need to find,

Q: Draw a space-division THREE (3)stages switches. There are 9 inputs and 16 outputs. Stage 1 has three…

A:

Q: Choose the correct instruction that will send data to an l/0 device IN AL, 60 IN 60, AL OUT 60, AL…

A: