THIS QUESTION REQUIRES A DOCUMENT UPLOAD A temperature control system has a binary input represented as ABCD, with A being the most significant bit. When the temperature is in an acceptable range we need the output of the control system to be one. We are in the acceptable pressure range when ABCD represents a decimal number from a minimum to 5 to a maximum of 12. When we are in this range the system output is one. However, if ABCD represents a decimal number of 4 or less, or 13 or more, the system should output a 0. a. Complete the truth table for this system b. Create a Karnaugh map for this system c. Based on the Karnaugh map, determine the simplest Boolean expression for this system d. Draw the simplified circuit that represents the Boolean expression found in step c. Complete your work on separate paper, then scan and upload your answer. YOU MUST SHOW ALL YOUR WORK TO RECEIVE CREDIT FOR YOUR ANSWER Upload Choose a File

THIS QUESTION REQUIRES A DOCUMENT UPLOAD A temperature control system has a binary input represented as ABCD, with A being the most significant bit. When the temperature is in an acceptable range we need the output of the control system to be one. We are in the acceptable pressure range when ABCD represents a decimal number from a minimum to 5 to a maximum of 12. When we are in this range the system output is one. However, if ABCD represents a decimal number of 4 or less, or 13 or more, the system should output a 0. a. Complete the truth table for this system b. Create a Karnaugh map for this system c. Based on the Karnaugh map, determine the simplest Boolean expression for this system d. Draw the simplified circuit that represents the Boolean expression found in step c. Complete your work on separate paper, then scan and upload your answer. YOU MUST SHOW ALL YOUR WORK TO RECEIVE CREDIT FOR YOUR ANSWER Upload Choose a File

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

digital signal processingsignal and systems
This question is from the subject Digital Logic Design. Assume your register number FA19BSExxx (excluding the dashes -) is in Hexadecimal, where xxx are the three digits of your registration number. a) Represent your registration number in the binary. b) Split the ten digits of your registration into two Hexadecimal numbers M and N, where the left most five digits make number M and the right most five digits make number N. Using r’s complement, subtract N from M. In other words, calculate M – N. Solve the question for registration no SP20-BCS-156.
Which system has a base 16? A. Octal B. Decimal C. Hexadecimal D. Binary
Write a program in assembly language to toggle PORTB 400 times. Use BNZ instruction.
After executing XLAT instruction, the content of system registers is: ES=4E25, DS=041C DI=6814, BX=0201, and AL =40, (all values shown are in hexadecimal and the addresses shown are physical addresses). What is the content of AL before executing this instruction? H. H. Address 20н 40 H 60 н 80 H A0H СОн E0 H Content 447C 447D 447E 447F 4480 4481 4482 Notes: 1- Use the memory fragment shown to answer this question. 2- Write down the final value of AL as two hexadecimal digits without any additional characters.
Electrical Engineering 1. Consider the following MIPS assembly language code: II: ADD Sl, S0, Ss1 LW S0, -4($s1) 13: ADD Sso, Ss0, Ss0 12: 14: SW S0, -4(Ss1) Which of the above instructions will have to be followed by a stall for the correct operation of the processor, given a 5 stage MIPS pipelined processor. 000
1) Before using an accumulator within a loop it has to be initialized. 2) _We cannot use functions if we do not include the function prototype. 3) If the number of arguments in a function call does not respect the function definition it causes a syntax error. 4) A pointer can point to variables of the same data type only. 5) We can have pointers to variables that are in the same function. T 6) If a function does not take input arguments and does not return any output, then, it cannot be defined as a function. F 7) We can have variable with the same name in different functions. T 8) _It is not possible to create a variable in the main function that has the same name as a function that we have already defined. T 9) _Global variables can be accessed by all functions I 10) Pointers are only used if the function has multiple outputs. F
a) An 8-bit shift register holds the data word 00111100. What will the register contents be after three right shifts? (Assume that serial input=D0) b) Draw the above shift register circuit using negative edge triggered D FFs
please help me on this
Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.
USE DIGITAL LOGIC AND DESIGN
Need complete correct and urgent answer.