Given the following circuit SW1 SW2 R1 200 Q R2 300 Q BAT1 R3 9 V SW3 400 Q 1) What is the value of the current through the battery when the switches SW1, SW2, and SW3 are OPEN? 2) What are the values of the voltages across the resistances VR1, VR2, and VR3 when the switches SW1, SW2, and SW3 are OPEN? 3) Determine which ONE switch, between SW1, SW2, and SW3, YOU need to close to cause the current of the battery to increases the most. Justify your answer with your calculations 4) Calculate the value of the current through the battery and the Voltage across all the resistors VR1, VR2 and VR3 when the switches SW1 and SW3 are closed, and the switch SW2 is open

Q: CEC Table 23 allows a maximum of ten wires in a certain box. However , the box will have two wire…

A: According to CEC Table 23, the maximum number of wires allowed in a box with two wire connectors and…

Q: 4. Name 3 methods how drawings are stored in?

A: Any single paper object or book would appear to be straightforward to keep and preserve on its own.…

Q: 14. Which of the following groups describes the three functions that an electrical device may…

A: Answer 14. Provide a breakpoint in a circuit, protect a circuit, and provide a control are the…

Q: A/An ________ captures different types of signals from the human body and convert them into…

A: The solution is given below.

Q: What dimensions are used when measuring the area of a building

A: According to National electrical code (NEC 220.12)  " outside area is used for the calculation of…

Q: Question 7 Draw a circuit that is a short circuit. Describe what is happening. If you are allowed to…

A: Draw a circuit that is a short circuit. Describe what is happening. If you are allowed to insert a…

Q: Which Insulators can be used for both horizontal and vertical positioning? A. SUSPENSION TYPE…

A:

Q: for this Lab you will be laying out and installing an emergency service panel. Emergency service…

A: (1)  General Emergency Power Systems provide automatic backup power in the event of normal power…

Q: Make a circuit that controls two LED's with a single switch; plus one of the LED's is controlled by…

A: Since you have posted multiple questions, according to guidelines, we will solve only the first…

Q: Fill in the blank: Electrical hazard boots are made up of highly materials.

A: Electrical Hazard boots are used to prevent the shock

Q: Determine the current, voltage and power

A:

Q: If three #10 AWG THHN/THWN wires were run in a conduit inside a building the MAXIMUM size fuse or…

A:

Q: This is a general question: How do smaller electrical engineering labs relate to building a…

A: Smaller electrical engineering labs can be very helpful in building a relatively larger system. This…

Q: Is there a way to clean up this answer by using proper notation

A:

Q: What are the quotient and remainder when - 35 divided by 4 ? -7 and -7 -8 and -3 O. -9 and 1 O. 9…

A: According to question we have to find the value of quotient and reminder.

Q: As an electrical and electronic engineer, your manager has asked you to write a report for the…

A: We need to write report on electric safety for different applications.

Q: if you have (10) 10 OHM resistors and (5) OMR resistors in a series circuit what would the total…

A: Resistances are given as,

Q: in this Lab you will be laying out and installing an emergency service panel. Emergency service…

A: (1)  Legally Required standby systems provide electric power to selected loads during firefighting…

Q: If you dont have a vise to hold a EMT conduit what other two methods could you use to hold the EMT…

A: To hold the EMT conduit in place while cutting with hacksaw, following items or methods can be used…

Q: Question 1 A microcontroller is used to control three LEDS in series (Blue, Red and White). Assume…

A: Here, we have asked to design an interfacing circuit to control three LEDs connected in series,…

Q: You wish to turn on the two LEDs located at the outside of the LED pack, so the first thing you will…

A: Al means lower 8bits of the accumulator here, we want to turn on the two LEDs located at outside of…

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.