Match each of the following from this giving graph ABCD CLA-0.SFT=1 Active O LOAD v After clock pulse 1, for the top figure what would be the output of a shift register when Clear Input=0 A. 1100 and none of the parallel data inputs are active? B. 0011 After clock pulse 2, for the top Figure what would be the output of a shift register when Clear Input=1 and B and C parallel data inputs are active? C. 1001 v After clock pulse 3, for the top Figure what would be the output of a shift register when Clear Input=1 D.010 and none of the parallel data inputs are active? E. 1111 v After clock pulse 4, for the top Figure what would be the output of a shift register when Clear Input=1 F. 0000 and none of the parallel data inputs are active?

Match each of the following from this giving graph ABCD CLA-0.SFT=1 Active O LOAD v After clock pulse 1, for the top figure what would be the output of a shift register when Clear Input=0 A. 1100 and none of the parallel data inputs are active? B. 0011 After clock pulse 2, for the top Figure what would be the output of a shift register when Clear Input=1 and B and C parallel data inputs are active? C. 1001 v After clock pulse 3, for the top Figure what would be the output of a shift register when Clear Input=1 D.010 and none of the parallel data inputs are active? E. 1111 v After clock pulse 4, for the top Figure what would be the output of a shift register when Clear Input=1 F. 0000 and none of the parallel data inputs are active?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Suppose you have a synchronous sequential circuit whose clock has a cycle time of 1800 ps (i.e., T. 1800 ps). The flip-flops have the timing characteristics given in Table 1 below. What is the maximum propagation delay of a combinational circuit between two registers? Give your answer in number of picoseconds (ps). For example, if your answer were 12 ps, you would enter 12. Table 1. Flip-flop Timing Characteristics Timing characteristic Amount (in ps) tpcq tcq 300 200 tsetup 150 thold 90
Consider a 5-bit right shift register each shifting data to the right for every clock pulse. The serial input A is derived by using NAND gates as shown in figure. If the initial content of the counter is 10001 at QOQ1Q2Q3Q4 by applying the clock signal then after how many clock pulse circuit is back to the initial state? Qo Q Q2 Q Q4 Register
For question # 2 in Web1, assuming the initial state of QO~ Q3 are 0100. Complete the timing diagram for six clock cycles. This is question # 2 in Web1: Question 2 Complete the timing diagram for this circuit, assuming all Q outputs begin in the low state: Clock Clock file 02987 Q₂ Q Q Q 10 D Q Ve God V God V Ve Cind V
Topic: Flip Flop ApplicationTrace the operation of the following sequential circuits, by drawing the timing diagram and creating the complete count sequence. (Note: Start at 0 initial state)
..
Please help me with the response diagram
Shift Register Operations 4-bit Parallel Data Output Qa QB Qc QD Serial FFA FFB FFC FFD Serial Data out Data in CLK CLK CLK CLK CLR CLR CLR CLR Clear Clock Figure 11.1: Serial input shift register (SISO+SIPO) 1. Test the circuit above (use your own input values) and note down the sequence of outputs in Table 11.1 after each successive clock pulse and obtain the timing diagram. Table 11.1: Truth Table for Shift Register COUNT QA Q8 Qc Qo 1 4 6. 7 8
4- Assume that we have 16 LEDS connected to our discovery board at PORTD from pin0 to pin 15 and assume that PORTD is initialized to work as a push pull output and the clock has been enabled for PORTD and the mode of the PINS connected to led has been chosen to be in output mode and the register GPIOD_ODR is used to write the output to the pins so that when the output is 0 the LED is off and vice-versa. Answer the following question int i; for (i=0;i=2){ GPIOD_ODR &="(1<<(i-2)); } } At each iteration what is LEDS that will be on from LEDO connected to PDO to LED15 connected to PD15.
kindly provide a logic diagram for my review. Thank you so much!
Design a 4-bit counter with one external input using T flip flop based on the following sequence: Input=0,6->2->9->13 (repeat), all undesired state go to 2. Input=1, 15->4->12->10 (repeat), all undesired state go to 4? *MIND TWO INPUTS THERE ARE i) State transition diagram = diag salag ii) State transition table such a example pic below iii) Simplification using 8 K-Maps required iv) circuit design
PLEASE HELP
consider what you would do for A, B, and C individually. Refer to the D latch diagram. For the given clock and D signals, what is the resulting output at Q? For the D register, using the same clock and D signals, what is the resulting outputs at -QL and QR? You can use the dashed boxes shown under the given signals for your answers, though you should provide a written explanation, too.