Homework Help is Here – Start Your Trial Now!
Engineering
Electrical Engineering
Effect t the n put Ress tance: Power Supply following Cireuit, Using DC for the power source. Set the DC supply's output Contrast the to above 5 V

Effect t the n put Ress tance: Power Supply following Cireuit, Using DC for the power source. Set the DC supply's output Contrast the to above 5 V

Introductory Circuit Analysis (13th Edition)
Introductory Circuit Analysis (13th Edition)
13th Edition
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:Robert L. Boylestad
Chapter1: Introduction
Section: Chapter Questions
Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...
See similar textbooks
icon
Related questions
icon
Concept explainers
Question
100%
Please do the calculated voltage please. Please write all formulas and write clear
**Title: Understanding the Effect of Input Resistance in Circuit Design** **Introduction:** This educational guide explores the impact of input resistance on the measured and calculated voltage in a simple electrical circuit. We will examine how to set up the circuit using a DC power supply and interpret the data collected. **Circuit Setup:** 1. **Power Source:** The circuit is powered by a 5V DC supply. 2. **Components:** The circuit includes a resistor connected in series with a voltmeter. 3. **Oscilloscope Connections:** - Positive terminal connected through a resistor. - Ground terminal connected to common ground. **Procedure:** - Connect the DC power supply set to 5V as shown in the diagram. - Measure the voltage across the resistor using an oscilloscope. **Data Collection:** | Resistance (R) | Calculated Voltage (V) | Measured Voltage (V) | |----------------|------------------------|----------------------| | 72.355 k-ohms | 2.42 V | | | 1 k-ohms | | 0.65 V | | 10 k-ohms | | | **Analysis:** - The table above shows the calculated and measured voltages for different resistance values. - Compare the measured voltages to the calculated ones to observe discrepancies and understand the influence of resistance on voltage reading accuracy. **Conclusion:** This experiment demonstrates the significance of considering input resistance in circuit design, especially when precise voltage measurements are required. Adjustments in resistance can lead to discernible differences in expected and actual voltages, highlighting the need for careful component selection and circuit configuration. **Note:** Always double-check connections and component values during setup to ensure accurate results.
Transcribed Image Text:**Title: Understanding the Effect of Input Resistance in Circuit Design** **Introduction:** This educational guide explores the impact of input resistance on the measured and calculated voltage in a simple electrical circuit. We will examine how to set up the circuit using a DC power supply and interpret the data collected. **Circuit Setup:** 1. **Power Source:** The circuit is powered by a 5V DC supply. 2. **Components:** The circuit includes a resistor connected in series with a voltmeter. 3. **Oscilloscope Connections:** - Positive terminal connected through a resistor. - Ground terminal connected to common ground. **Procedure:** - Connect the DC power supply set to 5V as shown in the diagram. - Measure the voltage across the resistor using an oscilloscope. **Data Collection:** | Resistance (R) | Calculated Voltage (V) | Measured Voltage (V) | |----------------|------------------------|----------------------| | 72.355 k-ohms | 2.42 V | | | 1 k-ohms | | 0.65 V | | 10 k-ohms | | | **Analysis:** - The table above shows the calculated and measured voltages for different resistance values. - Compare the measured voltages to the calculated ones to observe discrepancies and understand the influence of resistance on voltage reading accuracy. **Conclusion:** This experiment demonstrates the significance of considering input resistance in circuit design, especially when precise voltage measurements are required. Adjustments in resistance can lead to discernible differences in expected and actual voltages, highlighting the need for careful component selection and circuit configuration. **Note:** Always double-check connections and component values during setup to ensure accurate results.
Expert Solution
steps

Step by step

Solved in 4 steps with 1 images

SEE SOLUTIONCheck out a sample Q&A here
Blurred answer
Knowledge Booster
Measuring instrument
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:
9780133923605
Author:
Robert L. Boylestad
Publisher:
PEARSON
Delmar's Standard Textbook Of Electricity
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:
9781337900348
Author:
Stephen L. Herman
Publisher:
Cengage Learning
Programmable Logic Controllers
Programmable Logic Controllers
Electrical Engineering
ISBN:
9780073373843
Author:
Frank D. Petruzella
Publisher:
McGraw-Hill Education
Fundamentals of Electric Circuits
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:
9780078028229
Author:
Charles K Alexander, Matthew Sadiku
Publisher:
McGraw-Hill Education
Electric Circuits. (11th Edition)
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:
9780134746968
Author:
James W. Nilsson, Susan Riedel
Publisher:
PEARSON
Engineering Electromagnetics
Engineering Electromagnetics
Electrical Engineering
ISBN:
9780078028151
Author:
Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:
Mcgraw-hill Education,
SEE MORE TEXTBOOKS