ParagraphSStylesEditing1.The block diagram of a temperature control system is shown in Figure 1, where To is thedesired temperature and To is the output temperature.K3,++ToTDK₁Figure 1(a) Show that the transfer function relating To to TD is given by,K₁K₂TDTo=s+ K₁ K₂ K₂ +K₂ K₂Focus BEWC99+ibility: Unavailable12CKAK₂S15°℃Voice

Answered: Image /qna-images/answer/20b74ab0-bbc5-432e-8d4f-93df56a4a50a.jpg

Editing 1. The block diagram of a temperature control system is shown in Figure 1, where To is the desired temperature and To is the output temperature. K3. TD K₁ To Figure 1 (a) Show that the transfer function relating To to To is given by, T₁ = K₁K₂ S+K₂ K₂K₂ +K₂K, H (99+ lity: Unavailable Et K4 K₂ S Focus BO 15°C Voice E ^C

Editing 1. The block diagram of a temperature control system is shown in Figure 1, where To is the desired temperature and To is the output temperature. K3. TD K₁ To Figure 1 (a) Show that the transfer function relating To to To is given by, T₁ = K₁K₂ S+K₂ K₂K₂ +K₂K, H (99+ lity: Unavailable Et K4 K₂ S Focus BO 15°C Voice E ^C

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The output power of filter is 100 mW, when the signal frequency is 5 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ?
The implementation of a 4-1 multiplexer followingthe hierarchical design technique, …Requires four 2-1 multiplexers on one level ARequires three 2-1 multiplexers on one level BRequires four 2-1 multiplexers on two levels CRequires three 2-1 multiplexers on two levels DNone of previous answers E apparently the answer is D but i dont understand why so solve this question in great detail explaining every single bit of info as i'm a complete beginner and i need to understand how to solve questions of this type. also provide small examples of how the solution would differ if the question was slightly altered.
Draw a 2 Hz sinus function (amplitude is 2V). Calculate minimum sampling frequency. Draw the sampled signal with a sampling period of t=0.1s
Discrete Signals and Discrete Time systemsx[n1] = (values) 9 random integer values from -10 to 5x[n2] = (values) 9 random integer values from -5 to 5 a. Plot the graph setting the middle integer value at n = 0 showing the all samples.b. Plot the graph x[-n] showing all the samples.c. Plot the graph x[n-3] showing all the samples.d. Plot the graph x[n+2] showing all the samples.e. Plot the graph x[2n] showing all the samples.f. Plot the graph x[n/3] showing all the samples.g. Evaluate the convolution of x[n1] and x[n2].
Design with IC ‘555 and a capacitor of 9 uF: Monostable to get signal period=7 Astable to get frequency=2 Constraints: Use any resistor to be between 1K and 50K.
Determine the Nyquist sampling rate and the Nyquist sampling interval for the signals: (b) sinc² (10071) (c) sinc (10071) + sinc (50r t)
shows a block diagram of a process con- trol system. Determine the range of the gain K for stability. Figure K Figure Process control system. Verify using Nyquist on Matlab
2. Construct the state table and circuit excitation table for the state diagram given below. Use a D flipflop 1/0 0/o 1/0 0 1 0/o 11 1/1 1 0
| DSBSC signal generation using square wave information sign İnformation: 4 Vp-p 2 kHz square wave Carrier: 4 Vp-p 100 kHz sine wave How many sine waves does the DSBSC signal consist of and what is the frequency of these waves?
How to tell the difference between a open loop transfer function and closed loop transfer function?
Question 1 In this problem, you are required to design a 30-channel FDM multiplex for the transmission of voice signals. There are two bands available with the following frequency ranges: Band 1: 50 kHz - 80 kHz Band 2: 200 kHz - 230 kHz It is also required to have a 2 kHz guard band (no guard band is required is the beginning, i.e., before the first user) between each adjacent signal to avoid signal interference (for band 1). For band 2, 3 kHz guard band is required between each adjacent signal to avoid signal interference (no guard band is required is the beginning, i.e., before the first user). Draw a clear block diagram of your 30-channel. The diagram must show the number of stages of the multiplexer, the starting and the terminal frequency of each stage, the frequency of each guard band in each band, and the frequency of each user in each band (refer to last slide of chapter 4c pdf file). You should also describe the details of your design to get full credit.
5 a) Consider the sample sequence (5000, 5000, 5000, 5000, -5000, -5000, -5000, -5000}. These are samples of a square wave with a period of eight samples or 1ms at 16 KHz sampling frequency. What are the sinusoidal frequencies in the output waveform?