ec. Eng. Department Dr.Eng. Ammar All Sahrab Sheet of Questions A series RLC circuit with two elements value of R=250, and L=0.6H has a leading phase angle of 60° at frequency of 40HZ. Find the value of third element "C". At what frequency will the circuit be at resonance? Derive any expression will be used. Also, find: B, Q, o, & o? (Ans.: C=20µF, 6=45HZ, B=41.67 Q=6.9, @=267.9& 0,=309.57 rad rad sec

ec. Eng. Department Dr.Eng. Ammar All Sahrab Sheet of Questions A series RLC circuit with two elements value of R=250, and L=0.6H has a leading phase angle of 60° at frequency of 40HZ. Find the value of third element "C". At what frequency will the circuit be at resonance? Derive any expression will be used. Also, find: B, Q, o, & o? (Ans.: C=20µF, 6=45HZ, B=41.67 Q=6.9, @=267.9& 0,=309.57 rad rad sec

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the transfer function for the circuit shown in the figure. Plot the amplitude graph of 2log10[H(jw)] and the phase angle graph of H(jw) Calculate the actual cutoff frequency? Calculate the true phase angle at the cutoff frequency?
2. 10.2 mA 20⁰ R₂ = ∞n R₁ Design the network in the figure to have the following characteristics: i. BW = 500 Hz ii. Qp = 30 111. Vcmax 1.8 V (at resonance)
35
What is resonance? Explain how the condition of resonance is obtained in a series RLC circuit. Determine impedance, current, and power factor of RLC circuit at resonance.
b. Choose the suitable choice foL ping of the following sentences 18 Maces 1. In order to tune a parallel resonant circuit to a lewer frequency the capacitor must a. Be increase. b. Be decrease. . BeZero. Remain the same 2. Ina very low frequency a series resonance behaves as Imost purely .......... circuit a Resistive. b Capacitive. . Inductive. d. Inductive and capacitive 3. Real part of the total impedance at resonance for complicated AC circuit is a. Positive Value. b. Zero Value. Negative Value. d. Complex value 4. For admittance locus the maximum obtained power factor is depend on a Maximum current b. Maximum voltage . Minimum power d. Minimum angle 5 Any non sinusoidal symmetrical waves are basically composite from fundamental wave plas .. of harmonics waves. aodd b. even . odd even d odd of even 6. If we append an inductance in series to an RL series circuit the time constant will be a Increases b. Decreases. Increases and Decreases. Increases or Decreases 7. The double energy…
Ex. 1340. Refer to Figure setH(1340). Given: w1=1 rad/sec and G(s) = 34/s. Determine asymptotic (also actual): G1,G2,Ph1, mc where gains are in dB, frequencies are in rad/sec, and phases are in degrees. mc=Bode Plot type code. ans:4
For the electric circuit shown in figure below, find the value of ?the total power at resonance
i need the answer quickly
Q2 Sketch the asymptotes of the Bode plot magnitude and phase for the controlled transfer function of the system described in the figure, calculate the gain and phase: margins, Take K = 1. d42u42 S+
In Matlab for the transfer function
ASAP, please help now I will like.
*9. Design a series resonant circuit with an input voltage of 5V 20° to have the following specifications: a. A peak current of 500 mA at resonance b. A bandwidth of 120 Hz c. A resonant frequency of 8400 Hz Find the value of L and C and the cutoff frequencies. *10. Design a series resonant circuit to have a bandwidth of 400 Hz using a coil with a Q, of 20 and a resistance of 2 2. Find the values of L and C and the cutoff frequen- cies.