Each propeller of the twin-screw ship develops a full-speed thrust of F = 220 kN. In maneuvering the ship, one propeller is turning full speed ahead and the other full speed in reverse. What thrust P must each tug exert on the ship to counteract the effect of the ship's propellers? Assume a = 43 m, b = 139 m, c 10 m. F

Each propeller of the twin-screw ship develops a full-speed thrust of F = 220 kN. In maneuvering the ship, one propeller is turning full speed ahead and the other full speed in reverse. What thrust P must each tug exert on the ship to counteract the effect of the ship's propellers? Assume a = 43 m, b = 139 m, c 10 m. F

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question A rectangular pontoon 10 m long, 8 m broad and 3 m deep weigh 980 kN . It carries, on its upper deck, a boiler 6 m in diameter weighing 588 kN. Longitudinal axis of the boiler is parallel to 10 m side. The centres of gravity of pontoon and boiler are at the centroid of respective figures and in the same vertical line. Find metacentric height. Take unit weight of water as 9.80 kN / m³ . Boiler 6 m Pantoon 3 m B 8m G₁ O Elevation
Solve all the reaction. 10 KN/m El 2EI 5 m В 6 m C.
A closed cylindrical vessel of diameter 0.65 m is half filled with water and then rotated with its axis horizontal at a speed of 600 rpm. If the water rotates as a forced vortex at the same angular velocity as the vessel and takes the form of a cylinder with a hollow core, what would be the total axial thrust tending to burst the flat ends? Also determine the total axial thrust on the flat ends if the cylinder is completely filled with water and rotated with its axis horizontal at the same speed.
unit weight (c) mass density (d) specific gravity. The scow is 40 ft long, 20 ft wide, and 8 ft deep. It has a draft of 5 ft when floating in an upright position. The center of gravity of the scow is on the axis of symmetry, 1 ft above the water surface. Compute (a)the initial metacentric height and (b) the righting moment in fresh water when the angle of heel 0 is 10°. n A dam is triangular in cross-section with the upstream face vertical, Water is flushed with the 5.
A transmission tower is subjected to the wind loads shown. Determine the axial force (kN) in member GE. J 1.5 m K >7 kN 1.8 m H >3 kN 1.8 m D E >5 kN F 1.8 m В 2.55 m 2.55 m
Civil engineering -Hydraulics
Q2.characteristics of a small underwater craft are studied under dynamic similarity conditions in a varable density wind tunnel on a model scale of 1:12. What prototype speed and power are indicated by model values of 100m/sec of velocity and 30N of drag force? The model is operated at 8atm pressure [Take Pair at atmospheric pressure-0.95Kg/m³, Pwater-998Kg/m³. Hwater 1.0*103 pa.sec and Hair-2.17*105 pa.sec].
At the power station, a Pelton wheel produces 1260kW under a head of 610m. The loss of headdue to pipe friction between the reservoir and nozzle is 46m. The buckets of the Pelton wheeldeflect the jet through an angle of 1658, while relative velocity of the water is reduced by 10%due to bucket friction. The bucket/jet speed ratio is 0.46. The bucket circle diameter of thewheel is 890mm and there are two jets. Find the theoretical hydraulic efficiency, speed ofrotation of the wheel, and diameter of the nozzle if the actual hydraulic efficiency is 0.9 timesthat calculated above. Assume nozzle velocity coefficient, Cv = 0.98. Show the schematic diagram of this problem.
A rectangular scow 10m wide, 5m high, and 12 m long has a draft of 3m. Its center of gravity is at the center of the scow. If the scow is tipped transversely until one side is just at the point of submergence, find the righting moment.subject : hydraulics
4. A tubular steel [G= 80 GPa] shaft with an outside diameter of D = 100 mm and a wall thickness of t = 6 mm must not twist more than 0.05 rad in a 7-m length. Determine the maximum power that the shaft can transmit at 375 rpm.
A loaded scow has draft of 6ft in fresh water, when erect. The scow is 20ft wide and 40ft long and 8ft high. The center of gravity of the scow is 6ft above the bottom along the vertical axis of symmetry. What is the max. single weight that can be moved transversely from the center of the scow and unloaded over the side without sinking the scow?
Deflection at Q if the float at Q is eliminated and the reaction at Q if the float is placed back to its original position, are respectively P 0.379 m and 45.30 KN 0.781 m and 45.30 KN 0.651 m and 43.60 KN P = 80 KN 0.272 m and 43.60 KN Q+ Pontoons 15 m² each 8 mi 8m. w = 9.81 KN/m³ EI 180000 KN.m² R