Each of the box shown weighs 58 N and the inclined surfaces are smooth. The system is released from rest. Determine the magnitude of the velocities of the boxes when they have moved 1.43 m. 30° 45°

Q: Compute the value of P (kN) that will cause a zero deflection under P. 4 kN/m B Sm 2m 3m

A:

Q: Warm up Write down the formula of slope and deflection. Calculate the deflection at point D.…

A: The beam with the loading is given as E=200 GPaI=6.87×106 mm4 To find:- Formula of slope and…

Q: Determine the slope and deflection at point C of the beam shown by the direct integration method and…

A: Overhang beam with two point loads    NOTE : The question is solved by direct integration method…

Q: 6m note: Moment acts 1m from the free end. 20 kN/m 6m 700 kN-m 40 kN/m

A:

Q: Determine the vertical deflection at D (DDY) by used virtual work 500kg/m B 티 5,000kg/m 2EI 0 T E…

A:

Q: 1)Find the maximum defiection (inciluding its location), and the maximum slope (including its…

A:

Q: Find deflection at C and D. Using Moment- 22,500 lb Area Method 3000 lb/ft B D 4 ft 12 ft 6 ft 8 ft

A:

Q: Determine the vertical deflection at DIDDY) by used Castigliano's Theorem 500kg/m B 티 2EI 4.0 m.…

A:

Q: Determine the smallest moment of Inertia if the deflection at C should not exceed L/360 mm. [Use any…

A: Here we use double integration method for solving this problem Double integration method: Double…

Q: USE VIRTUAL WORK METHOD TO DETERMINE THE DEFLECTION AT THE MIDSPAN. 16KN 30 KN/m А B D 2.4 3.2 1.8

A:

Q: Determine the slope and deflection at point D for figure (b). Use the method of virtual work. (b)…

A: I1 = 16 × 108 mm4  I2 = 12 × 108 mm4 E = 210 GPA = 2.1 × 105 N/mm2

Q: (b) Find the rotation at "B" (c) Find the horizontal drift at "C" Given: [W24x94] Properties: E =…

A: E = 29000ksi I = 2700 in4 Find: (a) Rotation at B (b) Horizontal drift at C

Q: Determine the location and magnitude of the maximum deflection for the beam shown below using double…

A:

Q: Determine the deflection at the left overhang (left end) using either the Unit Load Method (Method…

A:

Q: Use Slope-Deflection Method to solve for the unknows on the 120mm x 120 mm beam shown in the figure.…

A:

Q: For the overhanging beam shown, determine the value of EIθ at point C. Use Virtual Work Method.

A:

Q: 2. The constant angular acceleration of the rotating disk is a = 16 rad/s². The angular velocity of…

A:

Q: 0.4m Given: Rod CD is rotating with an angular velocity o = 4 rad's CCW. Find: The angular…

A:

Q: A 1.5 5.0 40 kN/m 9.5 P (in kN) с 9.5 12.0 m P=201kN D E 200 kNm 1.0

A: Given data : Determinate beam with pinned and roller support at B and E respectively Find :…

Q: Determine the horizontal deflection at E (DEX) by used Castigliano's Theorem Ex 500kg/m B 2EI སླ…

A:

Q: calculate the maximum deflection if EI = 400 000 kNm^2 Note: moment acts 2 m from the free end. USE:…

A: Free body diagram:

Q: Answer fast.

A:

Q: A 2 m slender rod shown below slides along the horizontal and slope surfaces. At the instant shown,…

A: Given : Angular velocity of rod, ω = 2 rad/sec (clockwise)Angular acceleration of rod, α = 3…

Q: calculate the vertical deflection at point C

A: The figure given in the question is as follows:

Q: 1. Compute the magnitude of the slope at the left support and the deflection 1m left of the right…

A:

Q: Determine the largest value of couple moment M just before the disk begins to slip.

A:

Q: w = 15 KN/m E 200000 MPa I = 220x10°mm* 6m

A: The magnitude of uniform varying load, w=15KNmThe length of cantilever beam, L=6mModulus of…

Q: Determine the deflection at point B using Area-Moment Method. 900 kN 120 kN/m C -4 m 8 m

A:

Q: 40 kN 20 kN/m 10 kN A В C D 4m 3m 1m EI = constant

A:

Q: 2) A body weighing 2,225 N is being dragged along a rough horizontal plane by a force of 445 N.…

A: The given data is shown below: Weight of body=2225NForce=445Nf=112

Q: 5m QUESTION 2 Make use of the Slope Deflection Equations to calculate the Bending Moments at A, B, C…

A:

Q: Calculate the a.) Double deflection Integration b.) Area- Moment at point E Method Method c.)…

A: NOTE : Since you have asked multiple methods we will solve the first method for you. If you want any…

Q: 6kN ec and Ac - 4KN E = 200,000 MPa I = 9 x 107 mm4 4m 3m Fig.P15.1

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.