Each cord can sustain a maximum tension of 20 lb. Determine the largest weight of the lamp that can be supported. Also, determine 0 of cord DC for equilibrium.

Q: Determine the area of the moment diagram of the structure M O-ML OU2 OMI O ML/2

A:

Q: Give the location of the resultant from point O for the parallel force system

A: To find location of resultant from O

Q: E F D A Describe the load path of the applied force (of the man's weight) to the reaction points.…

A: Solution Assume man's weight = W The load path is  Its free body diagram can be  drawn as

Q: Define the maximum value of force P that can be applied on the system without causing buckling in…

A: The given simple frame is analyzed by using the equation of equilibrium forces. The algebraic sum…

Q: 5m 1.5 m 2m FB-60 N Fe=55 N 3m

A: Determine them which OA axes of flagpole and the angles θ and φ made between cables AB and AC.

Q: A roller BEoller rollerC

A:

Q: Determine the moment of the forces acting on the structure about point A. ´HIS IS AN EXAM. DO 90N…

A: In this question, Two forces of 90 KN and 20 KN are acting on the structure. 90 KN acts at 50 degree…

Q: CDEFGH is plate with a circular hole in it and has a unit weight p (N/m²). It is attached on DE beam…

A: Center of gravity: The point in a system where the total weight or mass of the body is assumed to be…

Q: Solve for the EI A using conjugate, beam method 400 N/m 400 N/m To 2.3m EIA @ pt. B CV 2.2m

A: Given:Required:deflection at point B using conjugate beam method

Q: 100 K 300 15m in roller on

A:

Q: SOLID STEEL SHAT 5m LONG IS STRESSED АT 80 МPа WHEN TWISTED THROUGH 4°. USING G = CAN BE TRANSMITTED…

A: Shear stress, twisted angle and it has been asked to determine diameter and power. Please refer step…

Q: regular rod is 3 meters long and weighs 100 Newtons, with ends A and B resting on two supports and…

A: To find support reaction at A and B

Q: H.W: Find forces and elongations wires, steel in each wire. A=80mm² L=4m E=200 G Pa Estrelaxation.…

A:

Q: Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A Member AB has…

A: Given : For member AB (helical spring) ; The radius of helical spring, R = 90 mm = 0.09 mNumber of…

Q: The frame system shown below consists of two, 3-m radius, frictionless pulleys at points B and D.…

A: Given  -

Q: Two circular shafts are joined together between fixed supports to resist a torsional moment of 80…

A: Solution:- Given data:- for steel part (AB) Hollow circular Do = 100 mm Di = 80 mm G = 150 GPa and,…

Q: The beam is loaded as shown. which of the following nearly gives the reaction at the roller support…

A: Draw the FBD of the beam. Then using equations of equilibrium the value of unknown reactions can be…

Q: HW (4-1): If the area of each bar of the truss shown in 2w figure is (2700 mm') and the movement of…

A: Calculate the moment about A as; ∑MA=01×10-RD×cos4.5°×10+RD×sin45°×30=0RD=-0.707 kN Calculate the…

Q: Two rods vertically connect beams AB and CD as shown in the figure. Point A is foxed supported while…

A: ASKED: To compute the force in the left rod.   Given, Modulus of elasticity (E) = 200 GPa or kN/mm2…

Q: The mass of the crate is 130 kg. Find the tension in the cables for equilibrium.

A: Free body diagram of equilibrium conditon: The wieght of crate is 130 kg, So, it is 130 kg x 9.81 =…

Q: The boiler has an inside diameter of 60.0 in. and a wall thickness of 1.000 in., and it is made of…

A:

Q: 6- The rectangular gat has dimensions 6 m by 2 m. Neglect the weight of the gate. Determine (a) The…

A:

Q: Problem 7.8 - Determine the values of the weight W and the suppor forces at A and B. The pulleys are…

A: To find support reaction and weight W

Q: Replace the three forces which act on the bent har by a force - couple system at the support point A…

A: Consider the following diagram: Draw the free body diagram of the system as follows:

Q: Q- A hollow shaft of external and internal diameters as 100 mm and 40 mm respectively is…

A: Given data- A hollow shaft- External diameter D=100 mm, Internal diameter d=40 mm, Speed N=120 rpm,…

Q: Draw the FBD. Then, determine the reactions at A and B. 650 N 500 N 30° 300 N 1500 N · m 60° B -5 m-…

A:

Q: Solve for this please. Thank you!

A: As there are two questions posted, according to guidelines only the first is being answered. Kindly…

Q: Situation 8: A couple acting on the winch at G slowly raises the load W by means of a rope that runs…

A:

Q: 4 Two plates (14 in x 2 in) are welded to an I-beam (W12 x 16). Find the moment of inertia with…

A: Width of plate (b) = 14 in  Depth of plate (d) = 2in W12 x 16 beam section    To find : Moment of…

Q: The beam is loaded as shown.What is the reaction at the roller?

A: Free body diagram -  Taking the span AB as horizontal axis, as it is asked to find only the…

Q: P9-1 D The steel rod (E= 200GPA) is subjected to the loading shown. If the cross-sectional area of…

A:

Electric Current, Voltage and Electric Power

The term electric current is the flow of electrons or electric charges. The drift of electrons is proportional to the amount of voltage or potential difference applied. The more is the voltage, the more will be the electron drift. The amount of electric current a circuit possesses is proportional to the density of electrons or electric charge.