() Figure Q2(d)e shows a toroidal core which is made of mild steel and it is wound with insulated wire.The induced magnetomative, force is 3014.3 AT while the circular cross section, A-A'is 300 mm?. Given that that the relative permeability of the mild steel, ur and the freespace permeability, lo are 220 H/m and 47x10-7 H/m, respectively.Sketch the magnetic circuit equivalent circuit of the above toroidal core.(i)Calculate the circumference of the core if the flux flows in the core is 500 µWb.(i)Identify the number of turns, N wound on the core if the current flowing in thecoil is 2.153 A.ViCalculate the airgar length (in the unit of mm) that need to be cut across the toroidal core if theflux produced in the core is 347.7 uWk and the magnetomotixe is 3014.3 AT.turn, NFigure 0?(d)

Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

(e shows a toroidal core which is made of mild steel and it is wound with insulated wire. The induced magnetomotive, force is 3014.3 AT while the circular cross section, A-A' is 300 mm?. Given that that the relative permeability of the mild steel, ur and the free space permeability, Mo are 220 H/m and 4x×10-7 H/m, respectively. (i) Sketch the magnetic circuit equivalent circuit of the above toroidal core. (ii) Calculate the circumference of the core if the flux flows in the core is 500 µWk. (iii) Identify the number of turns, N wound on the core if the current flowing in the coil is 2.153 A.

(e shows a toroidal core which is made of mild steel and it is wound with insulated wire. The induced magnetomotive, force is 3014.3 AT while the circular cross section, A-A' is 300 mm?. Given that that the relative permeability of the mild steel, ur and the free space permeability, Mo are 220 H/m and 4x×10-7 H/m, respectively. (i) Sketch the magnetic circuit equivalent circuit of the above toroidal core. (ii) Calculate the circumference of the core if the flux flows in the core is 500 µWk. (iii) Identify the number of turns, N wound on the core if the current flowing in the coil is 2.153 A.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A magnetic circuit consists of a cast steel yoke which has cross-sectional area of 200 mm? and a mean length of 120 mm. There are two airgaps, each 0.2 mm long. Calculate: (a) the m.m.f. required to produce a flux of 0.05 mWb in the airgaps; (b) the value of the relative permeability of cast steel at this flux density. The magnetization curve for cast steel is given by the following: B (T) 0.1 0.2 0.3 0.4 H (A/m) 170 300 380 460
Quastion 4: A ferromagnetic core whose mean path length is 12x102 m with a small gap of 3x104. The cross-sectional area of the core is 40x104 m2, the relative permeability of the core is 6000, and the coil of wire on the core has 700 turns. N= 700 turns Assume that fringing in the air gap increases the effective cross-sectional area of the air gap by 8%. Find: (a) the total reluctance of the flux path (iron plus air gap) (b) the current required to produce a flux density of 5.5 T in the air gap. I= 3x10 m A- 40x10 m k = 12x10 m
3 Biot-Savart for Curved Wire A segment of a closed current loop is shown in the following figure. Compute the magnetic field at the center of the semi-circle due to the straight and curved segments shown. b (Technically, to use the Biot-Savart law for currents in a wire, the current must be constant, and the wire must form a closed loop. As a result, there will be a contribution to the magnetic field at the origin due to the parts of the closed loop that are not shown. However, here we assume that the not- shown part of the loop is far enough away that they can be neglected.)
Explane for me how to solve the problem by the same steps as given , plese help
3. When you use complex notations for your field calculation, what is the physical consequence of a complex relative permittivity? Explain it in terms of field strength and phase.
5. a) According to this figure, if it's possible to create magnetic monopoles in a spherical closed surface, then find out the amount of total magnetic flux. N N N N
The figure shows a piece of wire curved in empty space with its left side half-circle and its linear parts assumed to be long enough. Determine the magnetic induction at point M if a constant I current flows through this conductor.
To a magnetic core, with a relative permeability of 2100, a current I1 of 1 A and a current I2 of 2 A are applied, where the number of turns of the winding is 1000. The depth of the magnetic core is 20 cm. take into account that the bounded measurements are given in centimeters. The air gap shown in the figure is 0.2 cm and has an effective area equivalent to 1.1 times the cross-sectional area of the core. Determine:a) The equivalent circuit with sources and reluctance (Graph it)b) The magnetic flux of the central columnc) Magnetic induction at point Ad) Explain what would happen if the flow of current I1 is reversed
10 Given a common magnetic core whose length is 100 cm, its cross-sectional area is 25 cm square. The relative permeability of the core material is 5000. Two coils are tightly wound on the core. N1 =1000 turns and N2 = 500 turns. The self-inductance of coil N1 will be: [ 7.85 m H 15.7 m H 3.927 m H 5.17 mH
The loop shown in the figure consists of radial lines and a circular segment centered at point P. Find the magnetic field ?⃗⃗ at point P...
Consider a charged particle moving with velocity v through a magnetic field B. The force F exerted by the magnetic field is always perpendicular to the velocity v. Select one: O True False Next page Assignment, Sem-3 AY 2020 -21 Jump to... ements oill lis SI O
I 4:30 docs.google.com/forms :D 3-Problems Problem-1: 00 The conducting wire shown in the adjacent figure is formed of four parts and traversed by a steady current I. R (1) 150 R a) Determine the magnetic field B, created by the semi-infinite wire (1) at point O. b) Derive the magnetic field Bz created by the curved part (2) at its centre O. c) Derive the magnetic field By created by part (3) at the centre O. d) Deduce the magnetic field B, created by part (4) at the centre 0.