E material has inner m'K, the temperatu

Q: n kn

A: given: ratio of linear strain and laterial strain known as?

Q: For twin steals, A SI01 is an oil Harding tool steel, a I SIS one is a shock resistant tool steel,…

A: Objective: To determine the given statement is true or false.

Q: 6. Way 28 mm diameter steel and 20 mm A composite beam made of aluminum rods in diameter. Elasticity…

A:

Q: What does it mean to be an independent slip system?

A: Slip system: It is a combination of slip planes along which the probability of deformation is…

Q: Cast iron is used to make rollers as it has superior compression load. Select one: True False

A: Solution:

Q: What does % elongation measures of?

A: Elongation: The increase in length of any object is known as elongation. The length of the object…

Q: Give an example of a flexure formula?

A: The flexure formula is also known as the flexure bending equation and is defined as; Where, M is…

Q: 18 It is given the nodule R=4. nunber of teeth z-25.please calculate the addendua circle (da),…

A: Given: The module, m = 4 The number of teeth, z = 25

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Write F if True and T if False. Marble and quartzite resemble each other in toughness and durability

A: Various mechanical properties required to define a material are: Hardness Toughness Durability…

Q: As the tempering temperature of a heat treated steel increases the associated values of Brinnell…

A: Tempering is a heat treatment technique applied to ferrous alloys, such as steel or cast iron, to…

Q: y=23 76 M=2 Find a,6, u

A: Given, Z1  = 23 Z2  = 76 m = 2   For d1 = Z1m = 23 * 2 = 46 For d2 = Z2m = 76 * 2 = 152 For a =…

Q: 13.Brass metal has high melting point.

A: Melting point of brass is 930 degree centigrade at atmospheric pressure.

Q: Whoop- ニフ P:?

A:

Q: The nominal diameter of V00 bolt is diameter. If safe tensile stres of the bolt

A:

Q: Differen bending neaf possible ach t

A: for solution refer below images.

Q: if the f Re 20 -0.25 mm %3D De terminef?

A: Relative roughness, eD=0.25Reynolds number, Re=20

Q: Clok on "add vertioal line off to add dicoontinulty linec. Then ollok on "add cagment" button to add…

A: To draw SFD and BMD

Q: Copper can be worked in hot condition Select one: True False

A:

Q: The formula for Critically Resolved Shear Stress is

A:

Q: 18. The part in Fig. 2-44 is made of 1045 steel, quenched and drawn, σult = 820 MPa, Typ = 620 MPa.…

A: Given: Mmin= 1040000 N.mm Mmax= 5000000 N.mm D=150 mm t= 25mm d = 75 mm

Q: Qus - The state of two dimensional stress acting on a concrete lamina consists of a direct tensile…

A: Given data  State of stress  Normal stress = 6 MPa  Shear stress = 4 MPa  Find the maximum tensile…

Q: What material and corresponding stresses is best for HP shape?

A:

Q: Mechime Desingn (welding) Q/find the Tmax far fiqure below : ch = 5mm $250N %3D 1 15mm bomm 300m…

A: given;   length of weld(l)=50mm thickness of weld (t)=5mm

Q: If diameter of solid shaft is halved and torque being transmitted is doubled, what will be change in…

A: Shear stress (τ) in the shaft of diameter (d) due to torque (T) can be given by, τ = 16Tπ d3…

Q: What do the two a's mean on the drawing? And how does one find that Fa-a acts to the right of the…

A: Given: width of key, d = 25 mm length of the key, l = 25 mm vertical force , F = 200 N allowable…

Q: For each of the structures shown in Fig.2, sketch the following: i. Free body diagrams showing the…

A: Given: FA = 300 lbf FB = 750 lbf

Q: A 100 ma 100mm Thok 100mm mm ; 100 mm, A=200mm E = 2006 Pa find 200 KN As 400mm? Reactions с

A:

Q: Defien the formula used to Determine the flexural rigidity D of the mat ?

A: given; Defien the formula used to Determine the flexural rigidity D of the mat ?

Q: lestion IJ alculate the maximum stress in 0.10-i 2.00-in dia. Applied torque %3D

A:

Q: same external tension load. Which pin has the lower shear stress?   O a. The solid pin on the…

A: Given:

Q: wrench size 18 cm, the lever force to be applied to the key and the tightening force of the bolt.

A:

Q: Q2) Sketch the various forms of set screw ends of size 16 mm diameter( at teast three).

A:

Q: ing 2omm

A: For solution refer below images.

Q: Mohr's Circle For Problems 10-70, determine the principal stresses and the maximum shear stress…

A: Given:To find:Labelled Mohr circle.

Q: Compressive stress is an example for stress Select one: O a. Direct O b. Indirect O .Combined O d.…

A:

Q: Gzd If (h=o.7 cm) for weld , find (Imax) for figure blow: l00 225mm of f=400W +50mm 45.27 Mlam?…

A: Given Data The force acting in the downward direction is: F=400 N The height of the weld is: h=0.7…

Q: 1 Demi e ARCndD

A:

Q: Define the term wide-flange sections?

A: Wide flange section Wide flange sections are those sections in which the flange of the section is…

Q: to k3 find ra) the global stiffness matrix.

A: First locate the nodes