a)Comment onthe relative errorof the numbers obtainedgivenonehadno ideaof the actual condition.b)If you glue strain gages on a plate loaded up edgewise, take readings and thencompute the state of stress,which assumption should you use and why? The stresses on a point in a steel plate were estimated to beOxx = 15 ksi (tension), oyy = 30 ksi (compression), Tyy = 25 ksi.Using E = 30 Msi, and G = 12 Msi, determine the strains ɛxx, Eyy, Yxy, Ezz and stress o2z under twoassumptions:a) Plane stressb) Plane strainc) Comment on the relative error of the numbers obtained given one had no idea of the actual condition.d) If you glue strain gages on a plate loaded up edgewise, take readings and then compute the state ofstress, which assumption should you use and why?

Answered: Image /qna-images/answer/f35cd2d4-7d5d-4470-8a3c-a16f63fbc18c.jpg

Answered: E = 30 Msi, and G = 12 Msi, determine…

Engineering

Mechanical Engineering

E = 30 Msi, and G = 12 Msi, determine the strains Exx, Eyy, Y ptions: ane stress ane strain

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The von mises criterion is to be used for yield predicitons of a given metal. Under plane strain…

A: The Von Mises criterion is to be used for yield predictions of a given metal.Objectives:Under plane…

Q: Explain the Stress Strain Relationship with the help of graph

A: We have to explain stress strain relationship

Q: A bending test is done on a specimen with the dimensions, Support span "L" is equal to 21 cm, the…

A: The expression for the stress is Substitute values in the above expression

Q: You find that the ultimate stress of an object is 15%. What does that mean qualitatively?

A: Given : Ultimate stress is 15% To find: What it means qualitatively

Q: Your manager asked you to explain the difference between three-point bending test and four-point…

A: The three-point bending test and four-point bending test are used to determine the bending strength…

Q: Two previously undeformed cylindrical specimens of an alloy are to be strain hardened by reducing…

Q: nm ha

Q: Your manager asked you to explain the difference between three-point bending test and four-point…

A: The force is F=30 kN. The thickness is t=5 cm=0.05 m The width is b=10 cm=0.1 m. The length is L=25…

Q: Problem 2 out of 2: A metal initially having a diameter of 8 mm and a gauge length of 40.0 mm is…

Q: In a forming process the diameter of the specimen is 1 cm and its length changes from 50 mm to 60…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

Q: 2- A tensile test specimen of stainless steel alloy having a diameter of 0.495 in. and a gage length…

A: Given: Dia-0.495 in. Gauge length = 2 in

Q: a) Material A is the strongest material (T) / (F) b) Material B is the most rigid material (T) / (F)…

A: As per the guidelines, we are bound to solve only 3 sub parts questions. Please repost the other…

Q: (a) Determine the magnitude of the maximum in-plane shear stress. (b) Determine the normal stress…

Q: Tensile test is a method to investigate the elasticity of a material. A test specimen is placed…

A: To explain: The stages that the specimen experiences before it breaks, and relate it with the…

Q: Consider the graph below for 3 test samples A, B and C of the same metal composition which have been…

Q: о ре cional area

Q: What is the Conventional Stress-strain show with a diagram?

A: A ductile material subjected to a tensile test passes through different stages before reaching the…

Q: The formula for Critically Resolved Shear Stress is

Q: If we want to measure the stress of a flat non-uniform component, what should we pay attention to…

Q: No wrong answer please , i could downvote The piece of suture is tested for its stress relaxation…

Q: In the First project: you have been asked to perform tensile testing for four different materials…

Q: Can we calculate true strain values at point M and F using ɛT = ln(1+ɛ)

A: Given data: Engineering strain at MεM=35%=0.35Engineering strain at FεF=53%=0.53 Need to determine…

Q: 2/ Aluminum tensile specimen with 12.5mm diameter, a gauge length of 50.8mm and the final ameter was…

Q: Part-A (Theoretical & Mathematical Problem) For the following state of stress, (a) using the general…

A: (a) Write the given stresses from the diagram. σx=20 ksiσy=-10 ksiτxy=-12 ksi Write the angle…

Q: A 10000N tensile force is used to pull a cylindrical rod with an initial diameter of 2 cm. During…

A: Given data: Tensile Force = 10000 N Initial Diameter of Cylinder = 2 cm Final Diameter of Cylinder =…

Q: For a certain metal, the strength coefficient= 700 MPa. A tensile specimen of the metal with gage…

Q: Correctly complete the following phrase below: "When a structure is subjected to general loading in…

A: The mechanical structure is subjected to two dimension general loading. The loads are static in…

Q: s ans soon ty

A: Given Data : Initial length of of iron piece(L)=108 mm Stressσ=786 MPa Deformation is entirely…

Q: The laboratory mechanism used to test the fatigue life of materials is Select one a. A rotating…

A: The fatigue test using the rotating-beam fatigue tester is the oldest method to determine the…

Q: ng the following (homogenous deformation, heterogeneous deformation, te tensile strength, yield…

A: The diagram is attached below:

Q: For ductile and linearly elastic material, stress is directly proportional to strain a. Below or at…

A: 1.Option (a) Below or at the yield point only. Is correct option Explanation: Stress is directly…

Q: The true stress (in MPa) versus true strain relationship for a metal is given by O = 1020 e0.4 The…

A: As per question given data σ=1020∈0.4∈=0.4initial area A =100mm^2 we have to determine the cross…

Q: Which of the following statement is correct? (a) The stress is the pressure per unit area. (b)…

A: Option d is correct: Stress is directly proportional to strain within elastic limit.

Q: Part D-Permanent elongation of the specimen if the specimen is loaded until its nominal stress value…

A: Givenσ=65ksiε=0.06

Q: Given, HRB = 4X Find BHN. Given, HRC = 3X %3D Find BHN.

A: Hardness : it is the property of the any material that tell the resistance ability to abrasion or…

Q: * For the following data, uning Mohr's cínele of stress and trigonometny, find the principal…

A: Given: σ1=σx=0σy=σ2=-20 ksiθ=30°(anticlokwise)

Q: A rectangular rosette is placed on a steel plate and indicates the following strains: Ej = 563 µm/m…

Question

a)Comment onthe relative errorof the numbers obtainedgivenonehadno ideaof the actual condition.

b)If you glue strain gages on a plate loaded up edgewise, take readings and thencompute the state of stress,which assumption should you use and why?

The stresses on a point in a steel plate were estimated to be
Oxx = 15 ksi (tension), oyy = 30 ksi (compression), Tyy = 25 ksi.
Using E = 30 Msi, and G = 12 Msi, determine the strains ɛxx, Eyy, Yxy, Ezz and stress o2z under two
assumptions:
a) Plane stress
b) Plane strain
c) Comment on the relative error of the numbers obtained given one had no idea of the actual condition.
d) If you glue strain gages on a plate loaded up edgewise, take readings and then compute the state of
stress, which assumption should you use and why?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

As Fast As you can Please mak sure the answer is correct 100% Please match the following to the appropriate areas or sublocations illustrated on the steel stress-strain curve shown below: (ultimate tensile stress- yield stress - repture stress) (4) The maximum stress point on the stress strain curve. (2) The point where the proportional limit ends and the moment the elastic limit of the specimen is reached, the specimen will return to its original state after the loading is removed. Typically occurs before the steel specimen starts to plastically yield. (5) The point at which the steel specimens has underwent necking and breaks. This typically occurs after the maximum stress is reached during the experiment.
New projections can illustrate the possible presence of angular strain. a True b False
Draw two schematic graphs using pencil showing a typical stress-strain curve for aluminum. The first graph should show engineering stress vs engineering strain, and the second graph should show true stress vs true strain. Label the showing: (i) elastic modulus (ii) proportional limit (iii) yield stress (iv)yield strain (v) fracture stress (vi) fracture strain on each graph. You may showboth graphs on one plot. Explain the difference between engineering stress and true stress.
Pleas very fast A square cross-section v-notched specimen of height 75 mm has each side of 13 mm has been selected to perform Charpy impact test. A v-notch of thickness 1.97 mm is made at the middle of the specimen length. Determine the cross-sectional area at notch. Cross-sectional area at notch (in mm2)
I need solution in word
please answer quickly
short Answer with Explaining all parts of the Question please
Write the definitions for engineering stress, true stress,engineering strain, and true strain for loading along a singleaxis.
Big and clear handwriting with all steps . Make sure calculations and answers are accurate please. THANK YOU
I am not reallyunderstanding what this problem wants with the wording, coud you help me clarify that please? Thank you so much!!
Please solve this in 15 min i will give the best feedback ,its urgent
A square cross-section v-notched specimen of height 75 mm has each side of 14 mm has been selected to perform Charpy impact test. A v-notch of thickness 1.75 mm is made at the middle of the specimen length. Determine the cross-sectional area at notch. Cross-sectional area at notch (in mm2)