E = 28 V - 4₁. + V₁ R₁ 12 ΚΩ 112 ΚΩ R3 3 ΚΩ Μ R₁ 9 ΚΩ R5 Μ 6 ΚΩ + Vs – R6 16 • 10.4 ΚΩ

Q: How can you use 2 to 1 Mux to construct 16 to 1 Mux.

A: 16 to 1 MUX using 2 to 1 MUX:

Q: Given that the diode is a Silicon diode, what is the voltage across the 5kN resistor? +12 V R,. 30…

A:

Q: Design a digitall to compute the 9 5 compliment of a binary coded decimalcode word. logic circvit…

A: Binary coded decimal digits exist only from 0 to 9 in decimal. The 9's complement of these digits is…

Q: Find the circuit needed to be used (schematic circuit using a zener diode )to protect the battery…

A:

Q: 30. For the input waveforms in Figure 5-61, what logic circuit will generate the output waveform…

A:

Q: Because of the limiting capability, the clipper circuits is also called a limiter. T

A: A wave shaping circuit that cuts off the top half or bottom half or both halves together of the…

Q: Draw the circuit of voltage doubler and Voltage quadruple. Explain the working of voltage doubler

A: Diode is used in wave shaping device. A circuit which give integral multiple of peak ac input is…

Q: The problem of reversibility in the series type ohmmeter is solved by Using half scale measurement…

A: Choose the correct option The problem of Reversibility in the series type ohmmeter is solved by...

Q: On part C, where did -0.7V come from? Part C is a whole different part than b, so I am confused how…

A: In general  we have to take  the base to emitter voltage of npn BJT as +0.7v where as for PNP BJT…

Q: Q9. The full subtractor circuit is implemented using D. one OR gate B. two AND gates A. two XOR…

A: here we have to identify by using which gates gates we can implement the FULL SUBTRACTOR.....

Q: Requirements You are required to create a functioning circuit that models some of the basic features…

A: According to the question, we need to design a circuit diagram based on the given conditions,…

Q: 1600 400 400 B. 16k

A:

Q: State which elements do and do not consume in an RLC circuit

A: Given : In the question they want to know for which range of frequency which element will consume…

Q: Draw the drain curve and discuss about the region of operation. When VGS is 4.5V and maximum drain…

A: (a) The curve for drain current s shown below

Q: 30. For the input waveforms in Figure 5-61, what logic circuit will generate the output waveform…

A:

Q: 2: Converting a decimal number to base b. Jump to level 1 Find the expansion base 4 of 54. Ex: 101

A: To convert the decimal number 54 to base 4

Q: The problem of reversibility in the series type ohmmeter is solved by Using half scale measurement…

A: Choose the correct option The problem of Reversibility in the series type ohmmeter is solved by...?…

Q: Im still confused on this may you break it down more for me

A:

Q: * current through R₁ (IR₁) * current through R₂ (IR₂ * Current through Di (ID₁) * Voltage Accross R₁…

A:

Q: The function HOLD ON is used to avoid erase of the first figure by the second one. O FALSE TRUE

A: No. Given statement is wrong.

Q: in step 2 is that 5r

A: here we need to explain the step 2 only

Q: What is the value of Vgs, when Id is .10 ?constant reference voltage Vdd =12V @

A: For a circuit, The reference voltage is 12V. and The drain current is constant.

Q: Draw a schematic of  the full-adder using a single 74153 IC.

A: Given: IC 74153 To do: Draw a schematic of  the full-adder using a single 74153 IC.   Note: As…

Q: This part which is also known as the dial or infinity knob allows you to adjust the pointer to the…

A: Adjustment screw is used .

Q: An LED is required to turn on when a switch is closed. The necessary illumination is obtained when…

A: The given circuit is as shown below, Given, LED forward drop, Vd=1.2V, LED current, ID=20mA.…

Q: Q3 What is the lock range of the PLL circuit for R1 = 4.7 kN and Cl = 0.001 µF, V=6v?

A:

Q: Calculate the minimum input voltage that will maintain the voltage across the load at 9 V when R=217…

A:

Q: When connecting an LED: Cathode needs to be connected to negative and Anode needs to be connected to…

A:

Q: Ammeter has a true value of 1.5 A. An analog indicating instrument with a scale of (0 – 2.5) A shows…

A: Given in the question: The true value of the current is: AT = 1.5A The measured value of the current…

Q: Write down state table of the following Circuit

A:

Q: 9 The total resistance of two resistors in series is the sum of their resistances. Determine the…

A: We need to find out worst possible error for given series combination .

Q: MAKE ONE ORIGINAL WORDED PROBLEM WITH DIAGRAM AND ITS FREE BODY DIAGRAM FOR OHMS IN SERIES…

A:

Q: Please find I and V values (Diodes are made of Si). + 3 V 12 k2 D; ▼ Dz 6 k2 - 3 V

A: Diode turns on when anode voltage is greater than cathode voltage and silicon diode maintains 0.7…

Q: NoR Gate Ov A o B aDt Dz +Sv

A: Given  Voltage drop of LED is 2V To explain the NOR gate logic

Q: Which one of following circuit is equivalent to OR operation? O a. B- O'b. A- DD- A. DD O d. A-

A: We know that bubbled NAND gate is equivalent to OR gate & Bubbled nor gate is equivalent to AND…

Q: Please help me make these two circuits on TinkerCAD. I am having trouble understanding how to make…

A: Need to connect the given circuit in the tinkercad and then analyze the circuit with various input…

Q: turn off time is the time

A:

Q: all the labeled current and voltages

A: Here β is not given . So assume β>> Q (large)So IB= 0means  IC=IESo  I1  = 5-(-5)91k +150k =…

Q: R X2 X3 1 -1 O 0.4 O 0.6 O 0.2 0.1

A: Fig: Given signal flow diagram In the above SFD  No. of the forward path  i x1x2 =1×1=1ii…

Q: 1 k2 Vin - SENSITIVE CIRCUIT

A: During positive half cycle of the input voltage both the diodes D1 AND D2 will turn ON. Or it is…

Type of Magnetic Material

Every material has a unique composition that defines its magnetic behavior. Some materials get attracted towards a magnet and are called magnetic materials. Based on the magnetic properties held by each material, they are classified into different types.