Determine the range of the force P required to keep the system stationary. P acts parallel to theground, and the coefficients of static friction at the contacting points are ?? = 0.2, ?? = 0.3,and ?? = 0.4. Both the 100-kg roller and 40-kg hollow cylinder have a radius of 150 mm (useg = 9.81 m/s2). Determine the range of the force P required to keep the system stationary. P acts parallel to theground, and the coefficients of static friction at the contacting points are 4A = 0.2, HB = 0.3,and µc = 0.4. Both the 100-kg roller and 40-kg hollow cylinder have a radius of 150 mm (useg = 9.81 m/s*).A30B.C

KINDLY REFER ATTACHED FILES FOR COMPLETE SOLUTION

Answered: e 100-kg roll

Engineering

Mechanical Engineering

e 100-kg roll

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.3P: Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair...

See similar textbooks

Similar questions

Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
The 60-lb plank rests on a frictionless roller at A, and the 20-lb triangular support BD. Both bodies are homogenous. The coefficients of static friction are 0.4 at B and 0.3 at D. Determine the largest force P that can be applied to the plank without initiating motion.
The mass of the unbalanced disk is m, and its center of gravity is located at G. If the coefficient of static friction is 0.2 between the cylinder and the inclined surface, determine whether the cylinder can be at rest in the position shown. Note that the string AB is parallel to the incline.
A cube with mass of m=80N is on the inclined plane with angle of phi=20 degrees. coeficient of static friction /mu_s = 0.25 coeficient of dynamic friction /mu_k = 0.15 Determine: what is the smallest size of the force F parallel to the inclined plane, which prevents the cube in the slide? what is the smallest size of the force F, which the cube starts to move along the inclined plane up? At what value of the force F starts the cube to rise at a constant speed?
3. Blocks A and B have a mass MA and MB, respectively. If the coefficient of static friction between A and B and between B and C is us and between the ropes and the pegs D andE µ's, determine the smallest force F needed to cause motion of block B. Given: E e = 45 deg Hs = 0.25 MA = 100 kg He's = 0.5 Mв 3 150 kg Р%3 30 N B m g = 9.81
Blocks A and B have a mass MA and MB, respectively. If the coefficient of static friction between A and B and between B and Cis ps and between the ropes and the pegs D and E ps, determine the smallest force F needed to cause motion of block B . Units Used: kN =103 N Given: ?=45deg s =0.25 MA =100 kg ps = 0.5 MB =150 kg P=30N g=9.81m/s2