During a flood event, stage recorders register headwater depth 4 m and tailwater depths 3.5 m of a culvert (measured above the culvert inverts). The 2 m by 2 m concrete culvert (square-edged entrance) is 10 m long and has a slope of 1%. Determine the flood flow rate that passed through the culvert. HW > 1.2D D The TW I

Q: R20

A:

Q: Determine the number of divisions required on the vernier scale, if it is combined with the main…

A: given- least count of main scale=0.5 mmleast count of combination of direct vernier=0.05 mm

Q: B 7m |C A 5m 6m 8m

A: Given: A tank filled with lubricant oil exerting 150 kPa Required: To find vertical stress increase…

Q: E A F D 3 in. in. G -2 in. 1.5 in B

A:

Q: Compute the total length of 10 mm diameter stirrups for a beam section 500 mm x 250 mm. Total length…

A:

Q: Determine the coordinates of the centroid for the shaded area

A:

Q: Calculate coordinate of centroid for a parabolic segment OAB which is +² bounded by the x-axis and…

A:

Q: 100 mm 150 mm

A:

Q: For the section shown below verify the following equations (7) Z section th'b' (b+h 12 (26+h B D C

A: Consider the given figure So here we have to verify J=t332b+hI12=th2b312b+h2b+h

Q: determine the centroidal axis xx of the section shown in the figure

A: The given section can be break into two rectangles, Let the unit of all dimensions are in mm,

Q: QUESTION 5 Which of the following represents the location of the horizontal plastic neutral axis (X,…

A: Solution Find the location of horizontal plastic neutral axis

Q: Determine: a) Differential Area b)  Centroid distance along x and y axis   *use 3 decimal places…

A:

Q: determine the distances x and y for equilibrium if f1=800 N and f2=1000N. (Hand written and clean…

A: Given data - F1 = 800 NF2 = 1000 N Find out - Distance x and y ?

Q: Find the centroid, ^y, and moment of inertia Ixx of the following sections.

A: The moment of inertia about X-Xaxis can be found using parallel axis theorem, IXX=IGG+A×h2IGG=MOI…

Q: p² – 3r + 2 lim r-1 r - 1

A:

Q: DRAW THE SECTION INDICATED BY THE CUTTIN

A: Any view obtained by a projection on a plane other than the horizontal, frontal, and profile…

Q: can u get the

A:

Q: 1" 5" 2" 1-Determine the location of the centroid (x,y) of the centroid. 2- Determine the Ix0 and…

A:

Q: Define deflection angles.

A: A deflection angle is an angle between the onward extension of the previous leg and the line ahead.…

Q: Why Nc=9 and Nq=1

A: Given question is based on static method of analysis bearing capacity of pile.

Q: 1) Compute the coordinates of the area centroid with respect to the given axes. 2m im 2m--- Zm- Im

A: To find centroid of given figure

Q: Find the Xp ¢ YT Зст I}1:25 cm Cocn 61.5 cm 0.75 cm

A:

Q: What does it mean if a beam is “non-compact

A: Beam is defined as a structural horizontal element which is used for resisting loads which are…

Q: 1. Find the shortest path from A to D. B 2 3. 2 G 5 F8E

A:

Q: Determine how far is the centroid of the given cross section above the base. 6-504 2-50" 9.0" 6.5"…

A:

Q: PROBLEM 1 Determine the x- and y-coordinates of the centroid of the shaded area. y 0 0 ♡ 100 y = 1+1…

A:

Q: Breaks the selected object .between two points You can create arc or line between two specified…

A: Given- Breaks the selected object .between two points   a) You can create arc or line between two…

Q: Lim x25X+ 2 2X+ 2X-1 .3 メ→。

A: To evaluate: limx→∞x2-5x+22x3+2x-1

Q: 80 mm -L- В D 60 mm

A:

Q: PROBLEM 2 The centroid of the T-section shown is 2.5 inches above the base. What should be the value…

A:

Q: D A E Given side B G Assuming that all stations are occupied and al lines are observed, what is the…

A:

Q: CORRECT ANSWER

A:

Q: 4x-2x2+1 find lim, 3x-5

A:

Q: y 25 45 55 25 65 80 I 55 165

A: Divide the given area into five parts as shown in part 1 of the question…

Q: ] Use graph paper to draw simplified sketch of the gear and the rack shown in problem 5/64(79). What…

A: Figure is as shown

Q: Determine the importance of utilizing an S-Curve in the field of Construction. Own words and atleast…

A: S Curve in construction: S-Curve is a chart or graph showing construction cash flows over a project…

Q: Find shape factor Q about the y-axis.

A:

Q: 11. Which IS codes gives details about elevators? A. O IS 27752 B. O IS 38665 C. O IS 14665 D. O IS…

A: IS code that gives details about elevators

Q: Calculate Q for a W10x15 cross section (A992).

A:

Q: Describe about the tangent modulus.

A: Tangent modulus:- The instantaneous rate of change of stress as a function of strain. The slope of…

Q: *9-64. Locate the centroid (, y) of the shaded area. y 1 in. 3 in 3 in. 3 in. Prob. 9-64 Ai=…

A:

Q: Xxccj

A: Xxccj - these are the word of the english language

Q: Which among the following determines the direction of closing error? a. Tan δ = ΣD/Σ O_b. c. d. Tan…

A:

Q: Determine the horizontal distance from O of the shear centre of the thin-walled beam section shown…

A:

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.