Dry and saturated steam at 6 MPa abs. enters a 40 m length of 11.5 cm O.D steel pipe at a flow rate of 0.12 kg/s. The pipe is covered with 5 cm thick asbestos insulation (k= 0.022 W/m-K). The pipe is located in a tunnel with stagnant air temperature of 27°C. The unit outside convective coefficient is 10 W/m^2-K. Neglecting steam film and pipe wall resistance, determine the mass of steam.

Q: Hot fluid "C 2562 J/kg.k, Pr-51.3, -522E-3 Pa.s, k-0.260 W/m.K" flows af 0.8 kg/min inside a water…

A: Given data as Cp=2562 J/kg.KPr=51.3μ=5.22×10-3 Pa.sk=0.260 W/m.Km˙=0.8 kg/min=0.0133 kg/sInside…

Q: A gas is cooled by circulating it in a turbulent regime through the interior of a circular duct with…

A: Given: The diameter of duct, Di = 0.025 m The internal wall temperature, Ti = 310 K The average…

Q: Water at 15°C (p = 999.1 kg/m3, cp 4.18 kJ/kg.K and u = 1.138E-3 kg/m. , k = 0.631 W/m.°C) is…

A: Solution:Given dataT1 = 15°cρ = 999.1 kg/m3cp = 4.18 kJ/kgkμ = 1.138×10-3 kg/msk =0.631 w/mCd =4.3…

Q: a) What is the required tube length for these conditions? b) To design a water heating system,…

A: first we calculate reynolds numebr  then evaluate nusselt number  then figure out h and the use…

Q: Water flows in a 3.5-cm-diameter pipe so that the Reynolds number based on diameter is 2000 (laminar…

A:

Q: Saturated liquid ammonia is entering a 50 cm diameter 10-m long pipe at a steady 0.1 kg/s mass flow…

A:

Q: HW Pressure Drop in a Pipe Water at 60°C is flowing by pump in a 0.0015-m-diameter 0.5-m-long pipe…

A: Given: T= 60o C Pipe diameter, d=0.0015 m length of the pipe, L=0.5 m average velocity, v=0.5 m/s…

Q: Engine oil flows at a rate of 0.05 kg/s through a section of a 2.5 cm diameter tube. The oil enters…

A:

Q: Consider the flow of oil (use unused engine oil properties) at 20? in a 30-cm-diameter pipeline at…

A: Solution:

Q: Air at 1 atm and 20 C flows in a 2.5-cm-diameter tube. The maximum velocity (m/s) of air to keep the…

A:

Q: 1. By increasing the flow rate, the overall heat transfer coefficient increases? Explain.

A: Solution o question (1) as per our company policy:

Q: Air at 10 °C enter an 18 m de long rectangular duct of cross section 0.15 m X 0.20 m at a velocity…

A:

Q: A tube with a square cross-section 2 mm in side and 1.5 m in length imposes a constant heat flux of…

A:

Q: Consider a 50-mm-diameter and 25-m-long smooth tube that is maintained at a constant surface…

A: Write the expression of the average temperature.Here  indicates inlet temperature and  indicates…

Q: A 10mm diameter and 20m long smooth tube is maintained at a constant surface temperature. Water…

A:

Q: . Corsidera circular soth pipeof inner diameter D;=0.015mwhose inner surface is covered with a layer…

A: GIVEN: INNER DIAMETER OF PIPE,D=0.015m FREE STREAM VELOCITY, V=1.2m/s AIR TEMPERATURE, T=300K AIR…

Q: Hot fluid "C= 2562 J/kg.k, Pr 51.3, u = 5.22E-3 Pa.s, k 0.260 W/m.K" flows at 0.9 kg/min inside a…

A: As given data as Cp=2562 J/kg.KPr =51.3μ=5.22×10-3 Pa.sk=0.260 W/m.Km˙=0.9 kg/min=0.015 kg/sInner…

Q: solve show all solutions and assumptions

A: Part aTo resolve this trouble, we want to use principles of warmth switch and fluid mechanics,…

Q: Air at 1 atmosphere and a temperature of 60f enters 1/2-in. id tube with a velocity of 80 fps. The…

A: Given information Pressure of air entering = 1 atmTemperature = 60°F = 288.7056 KDiameter of tube =…

Q: Heat transfer problem Water flows through a thin-walled cylindrical tube of diameter 1 cm,…

A:

Q: Problem 3: Insulation To=1 Toowwww Steam Tx2 T₂ T3 www www R₁ R₁ R₂ www.T R₂ Steam at Tx1 = 320 °C…

A: The objective of the question is to determine the temperature drops across the pipe and the…

Q: 21. In a repair shop compressed air is used to operate pneumatic tools. The total length of the…

A: Given Data The total length of the airline is:L=500 ft The inner diameter of smooth pipe is:I.D=0.5…

Q: a- Reynolds number R,- b- Entry length L,- c- Nusselt number, Nu =

A:

Q: Water (cp = 4197 J / kgC, k = 0.67W / mC, Pr = 2.2, dynamic viscosity = 352 * 10 ^ -6 Ns / m ^ 2)…

A:

Q: Industrial pipes Are stainless steel pipes more demanding about the flexibility design…

A: The objective of the question is to understand if the design flexibility of stainless steel pipes is…

Q: C Hot air enters a sheet metal duct located in a basement. Determine the exit temperature and the…

A:

Q: Twelve liters per minute of hot water at 330 K flow through a 0.5 inch schedule 40 (0.622 in wall…

A:

Q: A liquid is entering a 10 m long pipe of 0.2 m diameter at 25°C with an average velocity of 0.02…

A:

Q: determine the tube length required to heat the oil

A: Given: Di=3 cm Do=5 cm Ti=10oC To=30oC To determine:  Length of the tube

Q: Air at p = 1 atmenters a thin-walled (D = 5-mm diameter) long tube (L = 2 m) at an inlet temperature…

A:

Q: Hot fluid "C= 2562 J/kg.k , Pr=51.3, µ = 5.22E-3 Pa.s, k= 0.260 W/m.K" flows at 1.3 kg/min inside a…

A:

Q: Not Ai generated answers, I need to understand please show all steps.

A: Please refer below page.If you have any questions feel free to ask.Explanation:

Q: Hot fluid "C= 2562 J/kg.k , Pr=51.3, µ 5.22E-3 Pa.s, k=0.260 W/m.K" flows at 1.3 kg/min inside a…

A: Cp = 2562 J/kg.K Pr = 51.3 Dynamic viscosity, u= 5.22 * 10-3 Pa.s k=0.260 W/m.K Hot fluid flow rate,…

Q: Air at 10°C enters a 8 cm ID and 5 m long pipe at a rate of 3.5 kg/min. The inner surface of the…

A: Given data as per question Roughness =2mm Flow rate =3.5 kg/min Diameter of pipe =8 cm Length of…

Q: How is the Reynolds number related to Darcy-Weisbach?

A: Reynolds number is used to determine the nature of the fluid, Laminar or turbulent fluid.

Q: Air at 15 m/s is cooled from 80 C to 60 C in 2.5cm diameter tube. The tube wall is maintained at a…

A:

Q: Nak (56%/44%), which is an alloy of sodium and potassium, is used to cool fast neutron nuclear…

A: To findDetermine the tube length L and the local convective heat flux at the tube exit.GivenTube…

Q: Look at the following picture. Why do you think the entrance region can affect the analysis of the…

A: Dear student, entrance region or developing region is that region where the boundary layer is…

Q: The sensible heat-transfer coefficient for a dry surface has been determined to be 50 W/(m2-C) at a…

A: Given-Information:- Dry bulb temperature, Tdb= 24°C Wet bulb temperature, Twb = 18°C Area, A = 1m2…