Draw the voltage graph of the diode according to the voltage graph of the source in the circuit. 3 V 2V 6.36 V50 Hz/0 Deg 1 ka

Q: Find the ABCD constants of a circuit having a 650 resistor for the shunt branch at the sending end,…

A:

Q: Three long, parallel, straight wires each carrying a 8.0 A current pass through the vertices of an…

A: Given, Current through each wire, / = 8 A Length of the equilateral triangle, L = 8 cm = 0. 08 m The…

Q: Q4. Determine the equivalent inductance and equivalent current of the inductive circuit in Figure…

A: The circuit is shown below:  The equivalent inductance in all three branches is:  L1=5 mHL2=3…

Q: Q3. Calculate the branch currents and the total equivalent current of the complete circuit in Figure…

A:

Q: 2. A Half-bridge inverter with resistive load and capacitive elements is given in the figure. Vb =…

A: The RMS value of the voltage is: V0=1T∫0TV02dtV0=1TVDC22∫0TTV0=VDC2V0=722V0=36V And the minimum…

Q: The following network contains dependent current and dependent voltage source. Determine the h and g…

A:

Q: Q6. Calculate the total current in the circuit below if the circuit is powered by the sine wave…

A: The circuit is given as:

Q: Signals g₁ (t) = 10¹rect (10¹t) and 92 (t) = 8(t) are applied at the inputs of ideal low-pass…

A:

Q: Q1. Calculate the value of current through each resistor, the total current, and the total…

A:

Q: 3. For the A-connected load in the following figure, calculate a) The magnitude and angle of each…

A:

Q: A wave is traveling in the positive z direction with frequency = 1 MHz, and wave phase velocity of…

A:

Q: Find z and y parameters of the following network if they exist. 1:n Z, Ideal ele le

A:

Q: Consider a circuit given below. Find and plot v(t) for all times.

A: first draw the circuit for t < 0 and find the current through the inductor  then find t > 0…

Q: A 60-Hz three-phase transmission line is 180 mi long. It has a total series impedance of 40 + j150 2…

A: The problem is based on the analysis of different models of transmission lines. Short-line…

Q: If retransmission is not possible, is Automatic Repeat Request (ARQ) an effective correction…

A: Automatic Repeat Request (ARQ) is also known as Automatic Repeat Query. In a two-way communication…

Q: Simplify the following, implement the original and simplified equations with gates, and Ladder logic…

A:

Q: Q3) For the circuit shown in figure below, at V(0) = lv and a) Find the initial value of currents in…

A: "Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Calculate lo of the circuit shown in Figure 2 using the Superposition principle. 10 0 20 ww ww 50 10…

A: We have to find the value of current using superposition

Q: You are freshly employed in the design department of Tesla Motors. Your new job requires you to…

A: Given circuit shown

Q: 5. Explain the functions of Clark's and Park's transformations used in VFDS.

A: Explanation: Clark's transformation: Clarke transforms a three-phase equivalent right into a…

Q: For the circuit of fig. 1, a) Derive the output voltage expression vo in terms of R1, R2, Rf,V1, V2.…

A:

Q: Switch S was open for a long time. What total amount of charge goes through switch S after the…

A: When the same charge is present in all capacitors, they are said to be in series connection. When…

Q: Voltage amplifier R₁₂ MAR + AV1 Source R₂ + Vo Load 1. Using the voltage divider formula derive an…

A:

Q: Determine the Thevenin equivalent network at terminals a-b for the following circuit. 12 1F b. a 1H…

A:

Q: For the system shown in the figure below, find the sensitivity of the steady-state error for changes…

A:

Q: The switch S has been opened for a long time. At time t = 0, S is closed and is opened again at time…

A: .

Q: An input æ(t) = u(t) is applied to an LTI system which produces corresponding output y(t) = -2u(t–…

A:

Q: Consider the system G(s) = a) Sketch a Nyquist plot for G(s). b) Decide the phase and gain margins.

A:

Q: 4. A single phase full wave fullycontrolled (means all switches are thyristors) bridge rectifieris…

A:

Q: In the network figure below. Determine the VB, VC, VE, IE, IB, IC, and VCE. When vcC(V)=21 and B=184…

A:

Q: 2. A half-bridge inverter with a centre-tapped 280V battery has a 10 ohm load in series with an…

A:

Q: Consider the circuit seen in fig. 2. If the switch is closed at t=0, a) Write down the differential…

A:

Q: Find the time response Y (t) for the following system: Y (S) = (s+1)(s²+5s+4)

A: Laplace transform: It is the integral transform of the given derivative function with real variable…

Q: 5- Why should the terminal voltage drop more in the case of shunt generator than in the case of…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Which of the following current systems is most strongly correlated to the AE index? O A.…

A: The AE (auroral electrojet) index measures the strength of the eastward and westward electrojet…

Q: 4. A single phase full wave fully controlled (means all switches are thyristors) bridge rectifieris…

A: In this question we need to find a average voltage,RMS voltage , current and power transfer to load…

Q: A 60-Hz three-phase, three-wire overhead line has solid cylindrical conductors arranged in the form…

A: Given data f=60 Hz Spacing between the conductor; D=9 ft Diameter of the conductor; d=1 in To find…

Q: 10 cos(1000t), R = 100 Q, C = 100 µF , determine the expression If v(t) for i(t) .

A: Given data, The value of v(t) = 10cos100t The value of resistance is R = 100 Ω. The expression for…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.