Draw the shear, moment and axial load diagrams for each member of the frame. The joints at A, B, and C are pin connected. 25 kN 20 kN -2 m -2 m 2 m |A 6 m kN/m 45°

Q: 4-35 Draw the shear force diagram and moment diagram of the assembled beam. Each element is…

A:

Q: 6-65. Determine the horizontal and vertical components of force that pins A and B exert on the…

A: Given : Determine the horizontal and vertical component of reaction at A and B ?

Q: Determine the internal shear and bending moment at point C, which is just to the right of the roller…

A:

Q: 4 m 4 m 4 m | 4 m | 4 m | 4 m K J 6 m M |N H 60°- EQ P 60° 30° 30° 6 m D R 25 kN 25 kN 6 m C 6 m T 6…

A: compute the force in member FJ

Q: A 2 m 10 kN 2 m 10 kN 2 m- 15 kN.m B

A:

Q: etermine the moment at support A of the compound beam. Assume A is fixed a pin, and C is a roller. A…

A: To find moment at point A

Q: Compute the force in member BD in kN. P1 - 117 kN, P2 - 49 kN and x- 7.1 m. Nrite numerical value…

A: P1=117kN P1=49kN To find force in member BD

Q: Q.8 P The fixed beam ABhas a hinge MA Cat mid span. A concentrated load Pis applied at C. Whar is…

A: To find the moment MA =

Q: A pin connected frame is subjected to a hirizontal force of 240 kN at points C and D respectively.…

A:

Q: 1. Calculate the force in each member of the loaded cantilever truss by the method of joints.

A: Given : Using method of joints, firstly we will determine the support reaction and find the forces…

Q: S0 kN 40 kn/m lo kN/m

A:

Q: From the given cantilever truss shown supported by hinged A and roller at B. culate the force at FG.…

A:

Q: 5. 2 kN 0.8 m B -1 m- H -2 m- F -2 m- D 1 m 1.5 m E

A:

Q: For the beam shown, determine the maximum postive bending moment at point B due to the series of…

A:

Q: Determine the internal moments at each support. A is Pinned while C is Fixed. Use Moment…

A:

Q: the simply supported span.

A: Draw free body diagram Calculate the resultant of loads  R=4+6+8R=18kN Calculate the distance of…

Q: 10 kN 5 kN 5 kN \B C 2 kN/m 4 m A -3 m-2 m--2 m-3 m- (e)

A:

Q: Problem IV. Refer to the beam shown below. Internal hinges are installed at points C and E. 80 KN/M…

A:

Q: Use the cantilever method and determine (approximately) the reactions at supports A, B, C and D. All…

A:

Q: the cantilever method and determine tely) the reactions at supports A, B, C, and D. have the same…

A:

Q: 40 kN 3 m -3 m +3m A B C 35° E

A: Given data  Point load  Span length  Angle between members

Q: Determine the internal moment at joints F and G. 8m F A B 4m+ 8m 20 kN/m 8 m G D E 44m 4

A: To find the internal moment at the Joints F and G of the symmetric frame shown in the figure.

Q: Given the beam loaded as shown below, determine: (a.)Maximum shear in kN (b.)Maximum moment in kN-m.…

A:

Q: Determine reactions, shear force and bending moment. Draw SFD,BMD

A: Given : Determine reactions and draw the shear force and bending moment diagrams ?

Q: What is the required minimum thickness (mm) of a 3.2m long, simply supported one-way slab if its…

A: Concrete slab The concrete block may be a current structural part gift in numerous buildings that…

Q: E=200 x 10° N/m? A=300mm2 L=3m B. 3 m 4.5 m P.

A:

Q: 7. A single moving load of 80 kN is moves along a simply su The absolute maximum bending moment will…

A:

Q: QUESTION 4 member AD (carries only axial load) by FORCE METHOD. E=200KN/mm2, I=550x10°mm, A=1300mm2…

A: Force Method: Force method is also known as Method of Consistency and Method of consistent…

Q: 4-9. Determine the internal normal force, shear force, and bending moment in the beam at point C.…

A:

Q: Use the cantilever method and determine (approximately) the reactions at supports A, B, C and D. All…

A: To determine:Support reactions at A,B,C and D

Q: Draw (approximately) the moment diagram for column AGF of the portal. Assume all the members of the…

A:

Q: Problem Statement Based on Problems 7-33/34 from the textbook. Determine the normal force, shear…

A: W1=2kN/m W2=1.3kN/m To find internal force at point E and D

Q: Seatwork 3: Determine the internal shear, axial force and bending moment at point C. Assume the…

A: Determine the internal shear force, axial force and bending moment at point-C.

Q: A vertical column AB, of uniform section, 10 meters high, is hinged at the top and the base. It…

A:

Q: 1- Determine the internal normal force, shear force, and moment acting at point B, 1 m above the…

A:

Q: G H A 5 kN/m 81 8 m L I B 3 kN/m 8 m K J C 5 kN/m 8m F E D

A: It has been asked in the question to Draw the approximate moment diagrams for each of the five…

Q: ed ASAP

A:

Q: What is the maximum required spacing (in mm.) of the main reinforcement for a 120mm thick one way…

A: Given: A unit strip of a one-way slab of depth(d) = 120mm, and the yield-strength of steel as fy =…

Q: Determine the force in each member of the truss using methods of joints. State if the members are in…

A: