Draw the shear diagram for the beam. Follow the sign convention. (Figure 1) Click on "add vertical line off" to add discontinuity lines. Then click on "add segment" button to add functions between the lines. Note 1 - You should not draw an "extra" discontinuity line at the point where the curve passes the x-axis. Note 2 - The curve you choose from the drop-down is only a pictorial representation of a real quadratic/cubic curve. The equation of this curve is ne Consequently, slopes at discontinuities and intercepts with the x-axis (if any) are not accurate. 9 kN/m 9 kN/m |B - 3 m V (kN) - 3 m

Draw the shear diagram for the beam. Follow the sign convention. (Figure 1) Click on "add vertical line off" to add discontinuity lines. Then click on "add segment" button to add functions between the lines. Note 1 - You should not draw an "extra" discontinuity line at the point where the curve passes the x-axis. Note 2 - The curve you choose from the drop-down is only a pictorial representation of a real quadratic/cubic curve. The equation of this curve is ne Consequently, slopes at discontinuities and intercepts with the x-axis (if any) are not accurate. 9 kN/m 9 kN/m |B - 3 m V (kN) - 3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

16 R20 60 20 60 25 40 Command: 25 Front 02 30
50 24 D16 14 01810 50 25 6 Through h sketch the orthographic view using catia v5 , andi need the orthographic view in the first angle projection . also provide the isometric view note skip the question if you dont solve it or if you dont have the software, dont reject it. i need the solution any. please help
Please don't provide handwritten solution ......
MATLAB...Hand written plzzzz asap....FAST PLZZZZZZZZZZZ
Write MATLAB code to perform the following math expression: a) X=7, a=X+2 5 12 2 b) A= 22 L27 4 48 7
Write down any two methods of calculating product of a vector v and p
I am trying to find a Direction Cosine Matrix (DCM) for the Euler angle body 1-2-3 sequence. I tried making my own function and using the MATLAB function, but the result is matrices that are not equal to each other. But, if I were to use the 'ZYX' sequence, I would get a matrix that is equal to the transpose of the matrix produced by my function.I mean that transpose(EA123toDCM) = E123toDCM if I changed the sequence to 'ZYX'. I never got two equal matrices. Can you fix my code so I would get two equal DCM matrices for the body 1-2-3 sequence? Also, for the E123toDCM line, I am using the sequence 'XYZ'. Is that correct or should it be 'ZYX'? I know that that for a DCM of sequence 1-2-3 = R3(theta1)*R2(theta2)*R1(theta3). Is ZYX sequence the same as a 1-2-3 sequence? EA = [pi/3; -pi/4; -pi/6];EA123toDCM = EA123DCM(EA) E123toDCM = angle2dcm(EA(1,1), EA(2,1), EA(3,1), 'XYZ') function [R] = EA123DCM(EA) theta1 = EA(1,1); theta2 = EA(2,1); theta3 = EA(3,1); R1 =…
Please ASAP: (image provided) a) Create a function to solve a projectile problem where you are given initial x and y velocity, and the initial and final y position (inputs). You would like to use this function to find the final x and y velocity (outputs). This function will be used in the solution of the following problem. b) In the figure below, belt A moves with a constant velocity of 5 ft/s, and discharges sand onto belt B as shown. Assume that the angle of belt B is 15 degrees as shown. Write a MATLAB program to determine the required velocity of belt B if the relative velocity with which the sand hits belt B is (a) vertical, and (b) as small as possible. For part (b), use MATLAB to create a plot of the velocity of the sand relative to belt B, as a function of the velocity of belt B. Verify (either by hand, or by using MATLAB) that the minimum shown in this plot corresponds to the point at which the velocity of the sand relative to belt B is perpendicular to the velocity of…
CAM
Reduce the following block diagrams G1(s) R(s) + C(s) G2(s) G5(s) (s)9- G3(s) + G4(s) G7(s)
cos (8, + 02). The orientation of an object in 3D is given as: [cos (8, + 02) 0 - sin (0, + 02)1 R = Lsin (0, + 02) 0 cos (0, + 02) Where 0, and 0, are functions of time. Find the angular velocity matrix and the angular velocity vector of the object.