Draw the shear and moment diagrams for the loading condition shown. Show maximum shear and moment values. To get partial credits, show every step clearly while solving it. Circle the final answers. Make sure to use the correct units and show them with the numbers.

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Rolling: In this handle, the workpiece within the frame of slab or plate is compressed between two…

Q: When calculating "I", why have you used 50^3 x 24 rather than 24^3 x 50?

A: You have asked, When calculating "I", why have you used 50^3 x 24 rather than 24^3 x 50?

Q: From among the following select the truest statement. The Distortion Energy theory is a special case…

A: The given problem is based on theory of failure.

Q: What happens to an object's motion when the forces are balanced? Group of answer choices The object…

A: Balanced forces do not change the motion of an object. The motion of an object will not change…

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: Sorry that's the wrong answer it is 0.62

A: Power coefficient = Cp=0.24 Wind speed = Vw=10.3 m/s Blade length = R = 34 m The power generated by…

Q: From the following identify  the false statement . In general safety precaution the machine should…

A: Precaution and safety

Q: The circular rod shown in Figure 4 is subjected to a torque of 2000 kNm. Find maximum shear stress…

A: (a) The maximum shear stress in the shaft is 10185.9 MPa. (b) The rotation of the free end of the…

Q: When the diameter of cylinder is very small compared to its length, it can be treated as an…

A: As per given question  When the diameter of cylinder is very small compared to its length, it can be…

Q: Which of the following statements is true? Levers with a mechanical advantage less than 1 provide an…

A: Since the relationship of mechanical advantage to the motion is inversely proportional. This means…

Q: How would density be used to determine the concentration of antifreeze in the cooling system of an…

A: The density of antifreeze in the cooling system of automobiles is used to determine the…

Q: If rods of these materials are the same size, select the lightest metal rod. Titanium Carbon…

A:

Q: Particles less than in diameter are generally referred to as the fine mode: a. 0.75 μm; b. 7.5 um;…

A: This question is based on the concept of size of particles.

Q: Determine the x, y, z components of reaction at the thrust bearing D 0 = 0°.

A:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: - 2- 45 100lbs/ft 300lb 30 200lbs

A:

Q: If the cooling system operates above 100 degrees Celsius how should the cooling system, cooling…

A: The cooling system operates above 100 degrees Celsius how should the cooling system, cooling fans,…

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: when calculating the hc, why are adding the x as well ?

A:

Q: Determine the x, y, z components of reaction at the journal bearing C if 0 = 0°.

A:

Q: As the temperature of the nitrogen gas increases of same gas increases. Viscosity Weight density…

A: As the temperature of the nitrogen gas increases the viscosity of the same gas will also increases.

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.