Draw the shear and bending moment diagrams of the beams loaded as shown in the figures below. Round off reactions and magnitudes of shears and bending moments to 2 decimal places. TAKE NOTE W = 22kN/m , W1 = 15kN/m , P = 18kN and P1=9 kN

Draw the shear and bending moment diagrams of the beams loaded as shown in the figures below. Round off reactions and magnitudes of shears and bending moments to 2 decimal places. TAKE NOTE W = 22kN/m , W1 = 15kN/m , P = 18kN and P1=9 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a-3.25 m, b=4.75 m, Pg - 35kN, and Pc = 80kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A Ay- 58.66 - Dy- Calculate the reaction forces A, and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Answers: a 56.33 (a) V= (b) V- (c) V- B i i PB B kN с kN C Determine the shear force acting at each of the following locations: (a) x-2m (b)x - 4 m (c) x-8 m Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. 3 3 3 KN D b kN D ·x Dy
For the beam loaded as shown in the following figure, draw shear force and bending moment diagram and write their equations. Alsowrite values of shear force and bending moment in the diagrams at all change in loading points and the maximum shear and bendingmoments . where A=13kN/m, B=13kN, M=13/6 kN.m, C=13/6m
Question 2. The figure below shows a hollow circular beam with an outside diameter of 250 mm and a wall thickness of 20 mm loaded in bending with force F = 50 kN. F Ra I: Young's modulus of the beam is 60 GPa.. Calculate the second moment of area, I, in m4 in the form ax 106 where the number a is correct to two decimal places. M: 1 m x 10 m4 Calculate the maximum bending moment, M, in kilonewtonmetres (kNm): σ: kNm E: 1 m Calculate the maximum bending stress, o, in megapascals (MPa) correct to two decimal places. Rb MPa Hence, calculate the maximum compressive strain, e, Enter your answer in micro-strain correct to two decimal places: micro-strain Type here to search 91 DELL 80°F
The 1.5-in diameter solid steel shaft is simply supported at the ends. Two Pulleys are keyed to the shaft where pulley B is of diameter of 4 in and pulley C is of diameter of 8 in. Transverse shear stress needs to be considered. 1) Draw the bending moment diagrams of shaft AD for My and M₂, and indicate the location and the magnitude of the maximum bending moments. 10 in 200 lbf 1000 lbf 10 in 500 lbf 100 lbf 10 in F G E
For the beam shown in figure below, draw the shearing force and bending moment diagrams showing the main values. Also find whether there are points of zero shearing force and contraflexure. Knowing that AB=BC=CD=DE=3 m. A 9 kN/m B 30 KN Figure Q1 D 30 kNm E
QUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.
6. Q1: For the beam Shown in Figure 1 (40 Points) 8kN/m 3kN/m 8kN/m 1. Find the reaction at support B RBy, the bending moment at B, and the bending moment at C. B- A 2. Draw the shear force and bending 3m 2m 2m 3m moment diagram for the beam. Figure 1 Q2: (30 Points) For the simply supported beam with loading and cross section shown in Figure 2, determine the following: 1. The location of the centroid measured 10 kN 10 kN 100 from the top fiber in (mm). 2. The moment of inertia about the 50 centroidal x axis (mm“) 3. The maximum compressive stress in 0.6m 0.6 m 0.6 m 30 30 60 30, (MPa) 4. The maximum shear stress at the neutral axis in (MPa) All cross-section 5. The average shear stress on the section dimensions in mm (MPа) If the allowable stress in tension, compression, and shear are 4 MPa, 18 MP, and 12 MPa respectively. is this Figure 2 beam safe?
Draw a complete shearing force and a bending moment diagram for the for the beam shown in the figure. Show detailed calculations missing force F=171 kN. F KN 2 m B 10 kN/m A 10 m
QUESTION 1: For the cantilever beam shown in below figure, draw the shearforce diagram and bending moment diagram and determine: 1.1 The magnitude of the sheaforce at 3 m from the free end. 1.2 The magnitude of the bending moment at the fixed end. 2 kN 1.5 kN/m 2 m 2 m
1.Given Figure 3 determine the vertical reaction at C in kN 2.Given Figure 3 determine the location of maximum bending moment from A in m 3.Given Figure 3 determine the shear at B in kN 4. Given Figure 3 determine the bending moment at B in kN.m 5. Given Figure 3 determine the vertical reaction at A in kN6.Given Figure 3 determine the magnitude of maximum moment in kN.m
B7