Answered: Draw the shear and bending-moment…

Engineering

Mechanical Engineering

Draw the shear and bending-moment diagrams for the beam and loading shown following figures:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The cantilever beam in Figure 1 is fixed at A, and is loaded with a distributed load from A to B and a concentrated moment at C. Use the GRAPHICAL METHOD to plot the shear force and bending moment diagrams for the entire length of the beam. Label values at all key locations on the plots (at changes in loads, maxima, minima, and zeroes). Annotate your diagrams to explain how they were drawn (e.g. "AQAB = (-12 kN/m)(1 m) = -12 kN" and "(dQ/dx)AB = -12 kN/m"). 12 kN/m 5 kNm ZA B D 1 m 0.5 m 0.5 m Figure 1.
Part 1 For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let w = 9.5 kips/ft, a=10.5 ft, and b=22.0 ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Your answer is partially correct. Answers: By= Cy= Calculate the reaction forces By and C, acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Bx = 0, it has been omitted from the free-body diagram.) a 231.1875 B i 77.1875 W B b W b kips kips Cy X
Consider the simple span prismatic beam shown below, pin supported at the left end and roller supported at the right end, with a partial uniform load of 5 kips per foot and a 12 kip concentrated load applied at midspan as indicated (recall 1 kip = 1000 pounds). Complete the following: Sketch the shear and moment diagrams for the beam, indicating critical values for both shear and moment (maximum, minimum, etc.). Develop the equations describing the variation of shear and moment with x on the interval 4’-0 ≤ x ≤ 13’-0.
The beam in Figure 1; (a) Draw the Normal Force Diagram. (b) Draw the shear force diagram. (c) Draw the bending moment diagram. şekil 1 = figure 1 L1(m)=1.0 , L2(m)=1.4 , L3(m)=1.2 , M(kN.m)=20 , P(kN)=9 , q(kN/m)=8
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=4.00 m, b=5.25 m, c= 2.75 m, P = 36kN and M = 195kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A Answers: Ay= Cy= b Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) i i a M a B M B b kN 2 C KN C Cy C P с X P
3. Draw the load and the bending moment diagrams that correspond to the given shear force diagram in Figure 3. Assume no couples are applied to the beam.
2. The simply supported beam is loaded as shown in Figure 2. Neglecting the weight of the beam; (a) Derive the shear force and bending moment equations. (b) Draw and label the shear force and bending moment diagrams.
For the figure below, draw free-body diagrams for both the vertical and horizontal portions of the structure supporting the pulley and determine all reaction forces and moments. Then determine the shear and bending moment diagrams for both portions of the structure. Assume the mass of the structure and pulley are negligible. 48 in. 12 in. Cable 100 lb 12 in. pulley rad. 27 in. Cable 100 lb
Part 1 For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=14.0 ft, b-6.5 ft, c= 8.0 ft, w = 11 kips/ft and M = 210 kip-ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A Correct Answers: Ay = b Calculate the reaction forces A, and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Cy= 105.823 W 207.677 a W M a M B kips kips C b C Cy C C X
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a-3.25 m, b=4.75 m, Pg - 35kN, and Pc = 80kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A Ay- 58.66 - Dy- Calculate the reaction forces A, and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Answers: a 56.33 (a) V= (b) V- (c) V- B i i PB B kN с kN C Determine the shear force acting at each of the following locations: (a) x-2m (b)x - 4 m (c) x-8 m Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. 3 3 3 KN D b kN D ·x Dy
Problem 2 (a) Please compute and plot the shear force and bending moment diagrams for the beam shown below in Figure 2.1. Please use the method of sections to get the equations for shear force and bending moment, and use a computer to plot the diagrams and get the maximum value of bending moment. (b) For beam in problem 2-(a), suggest the lightest-weight wide-flange beam (use Appendix B) made of A-36 Structural Steel that avoids yielding with a factor of safety of at least 2. Use Sy (σy)=250 MPa. 50 kN/m Hinge 3@2m 6m = Figure 2.1
I need answer within 20 minutes please please with my best wishes