Draw the orthographic front view of the given image with proper dimensions.

Q: Find the velocity of point B and angular velocity in link 3 using relative analysis and polygon…

A: The angular speed of link O2A is ω2=1 rad/s The length of the links are…

Q: Draft and annotate the 2D sketch of housing using AutoCAD and mention all the dimensions. Colour the…

A:

Q: Given the following data, draw in a cartesian plane, the resulting vector,and it's three director…

A:

Q: For the compressor shown in the following figure, find the position of the piston with respect to…

A:

Q: flight information is as follows: Tower 1 - 300 km 15° EastofNorth @ 2:50 AM; Tower 2 - 250 km North…

A: taking scale,1cm=100kmso that,  1 to 2, 2.6cm=260km          2 to 3,  4.4cm=440km…

Q: How do we write the position or displacement equations for any angle of  theta shown with blue…

A: Given:To find:Position or displacement equations.

Q: Draw the orthographic views of the following isometric figure.

A:

Q: ompute the Degree of Freedom (DOF) for the given Kinematic diagram

A: To determine the degree of freedom for the given kinematics figures.

Q: Draw the isometric view of the given orthographic projection of the object?

A: According to the details in the kitchen we need to draw isometric view of the given object. I am…

Q: Draw the orthographic views of the following isometric figure

A: Given  3D model isometric view To find Orthographic view

Q: For the given isometric drawings, draw the corresponding top, front, and right side views

A: Note: As per policy, we can solve the first question from the multiple questions. Please resubmit…

Q: NL/H=493 and T₁ = 8 ms Give your answer to the 2nd nearest decimal place. Juve Ln transitions. What…

A: Given data T1=8ms=0.008 sNL/H=493

Q: Draw the isometric and orthographic sketch of the given figure (in catia V5 ;no hand drawing );

A: isometric view

Q: Draw the orthographic views of the following isometric figure. (units in mm

A:

Q: T= second last digit of your matric number. Example: if your 5 and 10+T - 10+4 - 14 (Answer in 2…

A: Given data S=2 T=0 Area of section ABCD= width× hight  = 10×52 = 520

Q: Give all the location dimensions between the datum target areas , A1 and A2. X = _________________,…

A: Give all the location dimensions between the datum target areas , A1 and A2.X =0  ,  Y =74   ,   Z =…

Q: To draw the vectors in graphical solution we need to specify first the scale of measurements. * O…

A: Correct answer: True

Q: A car has a velocity 176 ft/s. What is the velocity in MKS and CGS.

A: Given velocity of car is

Q: The given sketch is a cross section view of bracket. Sketch the 2D sketch of the below figure using…

A:

Q: 1

A:

Q: For the coordinate system shown, determine the DIAGONAL of the transformation matrix [Q] for the new…

A: Vector is a physical quantity that has magnitude and direction both. Scalar is a physical quantity…

Q: The part below has a variety of features that are labeled as datum features. Assume all are primary…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: Read and record the dimensions indicated by the letters A to H in Figures C-52a to C-52dⒸ. Figure…

A: From the given figure, it is clear that there are 8 divisions between two numbers therefore, value…

Q: Draw the orthographic views of the following isometric figure. (Units in mm)

A:

Q: Circle the letter corresponding to the correctly aligned set of orthographic views. 1. 2. A 6:6 A E…

A: according to the drawing data we need to find, the right option. that represent the three…

Q: Draw the isometric projection of the object showing the top, front and right side.

A:

Q: Draw the following views in Orthographic Third Angle Projection. 10:35 am 20 80 20 10:35 am

A: Given Data: Isometric view of the figure

Q: Using graphical method solve this problem:  Suppose you first walk A in a direction of B west of…

A:

Q: Draw the following using the figure given: 1. 45 degree CAVALIER 2. 45 degree CABINET OBLIQUE 3.…

A: According to the details provided in the question, we need to draw 1. cavalier oblique view  2.…

Q: For the compressor shown in the following figure, find the position of the piston with respect to…

A:

Q: Given two Orthographic views of an object, construct an Auxiliary view of the indicated ( —P)…

A:

Q: QI: Draw the orthographic Projections of given object. 20, 26 20 14 R20 35 SHOT ON REDMI 7 AI DUAL…

A: Orthographic projection is a two-dimensional representation of three-dimensional objects. It's a…

Q: Draw the one-point perspective of the object. The station point is 60 mm away from the picture plane…

A:

Q: In a rotating body, if it rotates at 2045 revolutions per minute.What would be the angular velocity…

A: Angular velocity Angular velocity is the rotational velocity of a body. It is equal to the angular…

Q: Draw the orthographic views of the following isometric figure. (units in mm

A:

Q: sketch the 2d figure using AutoCAD and mention the giwn dimensions

A:

Q: 20.00 60.00 40.00 FRONT 00 09 0002

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.