Draw the FBD, write equations of equilibrium, and solve for ALL support reactions. Determine shear and moment as a function of x – e.g. write the V(x) and M(x) equations. 4 kips/ft A B 5 ft 2 ft 8 kips 2 ft 8 kips

Draw the FBD, write equations of equilibrium, and solve for ALL support reactions. Determine shear and moment as a function of x – e.g. write the V(x) and M(x) equations. 4 kips/ft A B 5 ft 2 ft 8 kips 2 ft 8 kips

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

P= 13 kN In the given figure, all the dimensions, loading condition and cross-section of the beam are given. If the allowable tension stress om= 120 MPa and the allowable compression stress oeme=100 MPa ; q=2 kN/m \B 4m 1m a) Construct the internal force diagrams (N, T, M). b) Calculate the moments of inertia (I, I, I„.). c) Check whether the beam can carry the given loading safely. К.С. 2cm 8cm 2cm 4 сm C. |G X+ 9 cm Note: The modulus of elasticity in the material is E=200 GPa, K.Ç. :Line of forces Kiriş enkesiti
Calculate for the axial force in kN at member DC of the frame shown in figure 2 using Cantilever Method. Enter absolute value and use 2 decimal places in your solution. a = 39.4 kN, b = 39.2 kN, c = 2.7 m "a" kN D H "c" m "b" kN K "C" m "b" kN B F "c" m 4 m 5 m A = 40 x 10° mm? A = 60 x 10° mm? A= 40 x 10° mm? FIGURE 2
Determine the internal shear force acting at point C Determine the internal moment acting at point C
The beam carries various loadings as shown in the figure. An internal hinge is located at C. Calculate the maximum shearing force and maximum bending moment. What is the resultant reaction force and bending moment at support D? Draw the complete shear and moment diagrams on your solution paper
If the vertical component of the force F applied to the ring is 10 lb, determine the magnitude F and also the horizontal component. F 300
PROBLEM 1: The beam shown below has a fixed support at A and a roller at B. El is constant. Use the FORCE METHOD to: a. Find all reactions (clearly show the value and direction of each reaction at each support) b. Draw the Shear (V) and Moment (M) diagrams (clearly show the peak values, signs, and location) 4 kip/ft A 8 ft B *
Problem 1 Using the Moment-Distribution Method, determine the moments at B and C, then draw the moment diagram for the beam. Assume the supports at B and C are rollers and A is a pin. E = 29×10³ ksi, A = 6.49 in², I = 199 inª. 175 lb/ft -10 ft- B - 10 ft -8 ft 150 lb D
5. Using VWM or CTM, solve the slope of the elastic curve at the right support for the beam loaded as shown. EI is constant. A 3 m B 20 KN/m 2 m C 15 KN 1 m D
1 ft 3 ft B 3 ft 3 ft (-9002 + 800f + 1000k) Ib.ft 6 ft 3 ft E (-300î – 400ĵ + 100k) Ibs The applied force at point E and the applied couple moment at point D are shown in the figure. Complete/calculate the following: (Where applicable, express the results as the (x, y, z) components of a Cartesian vector) 1. Draw the free-body diagram (FBD), showing the appropriate reaction forces and/or moments at the supports. (You must show the reactions in their component form i.e. show RAx, MRAX etc. on the FBD). Note: The support at point A is not able to resist a moment about the 'X' axis but is able to resist a force in this direction. 2. The unit vector ÅBc 3. The position vector Tɛ/a 4. The position vector īB/a
Consider the figure below where each square is 1 ft on a side and A = 77 lb, B = 73 Ib, and C = 198 Ib. Calculate the resultant moment of the forces (in Ib-ft) about point O. Assign a positive sign convention for counterclockwise rotation and express your answer in two decimal places. A A B
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 3.3 ft, b = 3.2 ft, P = 20 kips, and w = 3.0 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. P A C D E Answer: (a) Vmax= (b) Mmax= a B b lb b lb-ft a