Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2

Q: Determine

A: The stresses acting on the planes are as follows:

Q: Q3/ The beam is subjected to a moment of 15 kip.ft. Determine the resultant force of the bending…

A: Given: The I section as shown

Q: La=zin J,O. 20in 3in N.A. 7nips 0,25 0.25 8 in

A: The above diagram can be shown as

Q: Consider the beam shown below. Take P = 5 kip and w = 1.7 kip/ft. Point E is just to the right of…

A: Solution:Given Data:The concentrated load acting on the beam is P=5kipThe intensity of uniformly…

Q: Can you explain in detal why the moment about x is -0.450(150)? from my point of view it should be…

A: See the explanation given below. Explanation:Step 1: Step 2: Step 3: Step 4:

Q: A rectangular timber beam, 320 mm deep by 140 mm wide, is located as shown below: 140 2 kN 1 KN ↓↓ 3…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: Required information For the beam and loading shown, consider section n-n. It is given that P= 226…

A: It is required to find the shearing stress at point b in beam section.

Q: The vertical shear in the beam is V 400 N, determine the average shear stress at points A and B. 100…

A: Shear force (V) = 400 N  Determine the shear stress at point A and B.

Q: A steel shaft with a circular opening on its centroidal axis is 2.54 meters long. It must carry a…

A:

Q: .T-profile cross-section overhanging beam is loaded as shown in the figure .a) Calculate the support…

A:

Q: 300 mm 30 kN/m 50 mm 40 kN c 50 mm A 350 mm 4 m 2 m 2 m 50 mm 200 mm a. Draw the shear diagram of…

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: Q2) The figure shows a cantilever consisting of steel channel size 127 mm×64 mm. Using…

A: Answer We know that the Superposition principle says that the effect of  combined loading is equal…

Q: For the beam width b determined in part (b), determine the maximum dead load PD that can be carried…

A: Given data: Live UDL load, WL=300 lb/ft Cross-section area of #6 bar, as=0.44 in2 Number of bars…

Q: Consider the overhang beam shown in (Figure 1). Suppose that P = 6 kN, M= 6 kN⋅m, w= 4 kN/m. Point D…

A: FIND REACTIONS:∑ MA=0RB3-124333+3-431.5+6-6356=0RB=23.2kN∑ Fy=0 By3-1243-43-635=0   RA=-1.6kN ∑ Fx=0…

Q: 8. A cast iron pipe of external diameter 40 mm, of internal diameter 20mm and of length 4 meter when…

A:

Q: Q3: Determine maximum bending stress in the strut and the orientation of the neutral axis. If the…

A:

Q: If the wide flange is subjected to a shear force of V = 30 kN, Draw the shear stress distribution in…

A: The maximum shear stress is the maximum concentrated shear force in a small area. The neutral axis…

Q: A cantilever beam AB, loaded by a uniform load (see figure), is applied on a channel section. If the…

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.